Difficulty
Moderate
Steps
13
Time Required
30 minutes
Sections
3
- Base Panel
- 3 steps
- Battery
- 5 steps
- Motherboard
- 5 steps
Flags
0
BackDell Latitude 9410 2-in-1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Base Panel
- Ensure that the laptop is unplugged and powered off before beginning.
- Place the laptop upside down on a flat surface.
Ensure that the laptop is unplugged and powered off before beginning.
Place the laptop upside down on a flat surface.
1024
Step 2
- Use a Phillips #00 screwdriver to loosen the ten captive screws.
- The screws are permanently fastened to the base panel; do not attempt to remove them.
Use a Phillips #00 screwdriver to loosen the ten captive screws.
The screws are permanently fastened to the base panel; do not attempt to remove them.
Step 3
- Carefully lift off the back panel.
Carefully lift off the back panel.
Step 4
Battery
- Use a Philips #00 screwdriver to remove the five 3mm screws that secure the battery.
Use a Philips #00 screwdriver to remove the five 3mm screws that secure the battery.
Step 5
- Use a Philips #00 screwdriver to remove one 4.5 mm screw.
Use a Philips #00 screwdriver to remove one 4.5 mm screw.
Step 6
- Grip the battery cable near the plug and pull it straight out, in the direction of the cable.
Grip the battery cable near the plug and pull it straight out, in the direction of the cable.
Step 7
- Use tweezers to gently move the speaker ribbon cable away from the bottom of the battery.
- The ribbon cable is thin and fragile; handle it carefully.
- The ribbon cable only needs to be moved so that the battery can be removed; do not completely remove the ribbon cable.
Use tweezers to gently move the speaker ribbon cable away from the bottom of the battery.
The ribbon cable is thin and fragile; handle it carefully.
The ribbon cable only needs to be moved so that the battery can be removed; do not completely remove the ribbon cable.
Step 8
- Lift the battery out with two hands.
Lift the battery out with two hands.
Step 9
Motherboard
- Use a Philips #00 screwdriver to remove the two 2 mm screws that secure the fan.
Use a Philips #00 screwdriver to remove the two 2 mm screws that secure the fan.
Step 10
- Disconnect the two ribbon cables connected to the motherboard by lifting the black ZIF tab and pulling the ribbon cables free.
Disconnect the two ribbon cables connected to the motherboard by lifting the black ZIF tab and pulling the ribbon cables free.
Step 11
- Disconnect the two Wi-Fi card cables by prying them up and away from the press-fit connector.
Disconnect the two Wi-Fi card cables by prying them up and away from the press-fit connector.
Step 12
- Disconnect the small black wire from the mother board by pulling in the direction of the cable.
- Disconnect the black and red wire from the motherboard, also by pulling the direction of the cable.
Disconnect the small black wire from the mother board by pulling in the direction of the cable.
Disconnect the black and red wire from the motherboard, also by pulling the direction of the cable.
Step 13
- Use a Philips #00 screwdriver to remove the eight 3 mm screws that secure the motherboard.
Use a Philips #00 screwdriver to remove the eight 3 mm screws that secure the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Brenden William Johnson
Member since: 10/04/2022
313 Reputation
3 Guides authored
Badges:
4
+1 more badge
Team
The Citadel Military College of South Carolina, Team 3-16, Eggleston Fall 2022
Member of The Citadel Military College of South Carolina, Team 3-16, Eggleston Fall 2022
CMCSC-EGGLESTON-F22S3G16
3 Members
3 Guides authored
