Difficulty
Moderate
Steps
11
Time Required
30 minutes
Sections
2
- Motherboard
- 10 steps
- Rear Facing Camera
- 1 step
Flags
0
BackDell Latitude 10-ST2e
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Motherboard
- Using the blue opening tool, separate the back plastic cover from the device. Start in a corner, and work your way around the tablet.
Using the blue opening tool, separate the back plastic cover from the device. Start in a corner, and work your way around the tablet.
1024
Step 2
- Remove the four 4.0mm black screws on the perimeter of the device using a JIS #00 screwdriver
Remove the four 4.0mm black screws on the perimeter of the device using a JIS #00 screwdriver
Step 3
- Remove the two 4.0mm silver screws using the JIS #00 screwdriver.
Remove the two 4.0mm silver screws using the JIS #00 screwdriver.
Step 4
- Disconnect the connection of the front camera clamp by releasing the clamp with tweezers.
- Pull up on the connection from the motherboard.
- Avoid damaging the connection.
Disconnect the connection of the front camera clamp by releasing the clamp with tweezers.
Pull up on the connection from the motherboard.
Avoid damaging the connection.
Step 5
- Using an opening tool, lift upwards on the white clamp, and pull the blue tab out of the connection with tweezers.
Using an opening tool, lift upwards on the white clamp, and pull the blue tab out of the connection with tweezers.
Step 6
- Using tweezers, disconnect the white and black wires from the bottom of the motherboard.
- Pull upwards while holding the brass connections. Do not pull on the wires.
Using tweezers, disconnect the white and black wires from the bottom of the motherboard.
Pull upwards while holding the brass connections. Do not pull on the wires.
Step 7
- Disconnect the two clamps, one orange and one white, using tweezers next to the battery.
Disconnect the two clamps, one orange and one white, using tweezers next to the battery.
Step 8
- Remove the four 7.0mm screws securing the battery with a JIS #00 screwdriver.
Remove the four 7.0mm screws securing the battery with a JIS #00 screwdriver.
Step 9
- With the blue opening tool, gently lift up and remove the battery from the tablet.
- Do not damage, puncture, cut, or bend the battery, as this may cause bodily harm.
With the blue opening tool, gently lift up and remove the battery from the tablet.
Do not damage, puncture, cut, or bend the battery, as this may cause bodily harm.
Step 10
- Rotate the motherboard upwards from the tablet using tweezers, but do not remove completely from the device. As you lift, disconnect the black and red wire located underneath the motherboard before removing it completely from the tablet.
Rotate the motherboard upwards from the tablet using tweezers, but do not remove completely from the device. As you lift, disconnect the black and red wire located underneath the motherboard before removing it completely from the tablet.
Step 11
Rear Facing Camera
- Once the motherboard is removed, place on a flat surface facing down. Use the plastic opening tool to disconnect and remove the camera from the motherboard.
Once the motherboard is removed, place on a flat surface facing down. Use the plastic opening tool to disconnect and remove the camera from the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Jan Camacho
Member since: 09/27/2017
140 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
USF Tampa, Team S16-G4, Eyestone Fall 2017
Member of USF Tampa, Team S16-G4, Eyestone Fall 2017
USFT-EYESTONE-F17S16G4
4 Members
12 Guides authored
