Difficulty

Moderate

Steps

17

Time Required

                          20 - 25 minutes

Sections

4

  • Battery
  • 3 steps
  • Keyboard
  • 6 steps
  • Top Cover
  • 4 steps
  • Fan
  • 4 steps

Flags

0

  • BackDell Inspiron 14R (N4010)

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Make sure the laptop is not plugged into any wall outlets or the charger
  • Unlock the battery by sliding the right-hand switch to the right.

Make sure the laptop is not plugged into any wall outlets or the charger

Unlock the battery by sliding the right-hand switch to the right.

1024

Step 2

  • While holding the left-hand switch to the left position, pull the battery away from the laptop.

While holding the left-hand switch to the left position, pull the battery away from the laptop.

Step 3

  • The battery is now fully removed and the laptop will not power on without it.

The battery is now fully removed and the laptop will not power on without it.

Step 4

              Keyboard
  • Using the #0 Philips head, unscrew the indicated screw.
  • Carefully pull the RAM cover up and away.

Using the #0 Philips head, unscrew the indicated screw.

Carefully pull the RAM cover up and away.

Step 5

  • Unscrew the indicated 5.7mm screw beneath the RAM Cover.

Unscrew the indicated 5.7mm screw beneath the RAM Cover.

Step 6

  • Remove another screw above the battery release tab

Remove another screw above the battery release tab

Step 7

  • Using a thin plastic tool (such as a guitar pick or spudger) at the top of the keyboard just above the F7 key, gently pry the keyboard away.
  • Move the spudger to either end at the top of the keyboard to fully undo all plastic clips.

Using a thin plastic tool (such as a guitar pick or spudger) at the top of the keyboard just above the F7 key, gently pry the keyboard away.

Move the spudger to either end at the top of the keyboard to fully undo all plastic clips.

Step 8

  • Carefully tip the keyboard upwards and pull it slightly away from the body of the laptop.
  • Be careful not to put stress on the ribbon cable below.

Carefully tip the keyboard upwards and pull it slightly away from the body of the laptop.

Be careful not to put stress on the ribbon cable below.

Step 9

  • Carefully unclip the ribbon cable by tipping the keyboard towards the screen.
  • The keyboard is now completely disconnected.

Carefully unclip the ribbon cable by tipping the keyboard towards the screen.

The keyboard is now completely disconnected.

Step 10

              Top Cover
  • Remove the indicated 5.7mm screws.
  • Remove the smaller 3mm screws from underneath the battery compartment.

Remove the indicated 5.7mm screws.

Remove the smaller 3mm screws from underneath the battery compartment.

Step 11

  • With a plastic spudger, pry away the silver top cover from the black casing.
  • Move the tool to the right and left along the seams to fully disconnect the cover.

With a plastic spudger, pry away the silver top cover from the black casing.

Move the tool to the right and left along the seams to fully disconnect the cover.

Step 12

  • Disconnect the indicated ribbon cables underneath where the keyboard sits.

Disconnect the indicated ribbon cables underneath where the keyboard sits.

Step 13

  • Lift the cover upwards and away from the body of the laptop, after removing the optical drive and unscrewing the three screws on the right

Lift the cover upwards and away from the body of the laptop, after removing the optical drive and unscrewing the three screws on the right

Step 14

              Fan
  • Peel back the yellow tape to expose the ribbon connector.
  • Unplug the ribbon cable from the motherboard.

Peel back the yellow tape to expose the ribbon connector.

Unplug the ribbon cable from the motherboard.

Step 15

  • Unplug the 3-wire connector from the motherboard.

Unplug the 3-wire connector from the motherboard.

Step 16

  • Unscrew the indicated 5.6mm screws with the #0 Phillips Head Screwdriver.

Unscrew the indicated 5.6mm screws with the #0 Phillips Head Screwdriver.

Step 17

  • Remove the fan from the device.

Remove the fan from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Andre Tomlinson

Member since: 09/27/2017

101 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       USF Tampa, Team S13-G5, Boczar Fall 2017                        

                                                  Member of USF Tampa, Team S13-G5, Boczar Fall 2017 



                    USFT-BOCZAR-F17S13G5                     


                                            5 Members                     


                                            9 Guides authored