Difficulty

Moderate

Steps

14

Time Required

                          25 minutes

Sections

9

  • Battery
  • 3 steps
  • Optical Drive
  • 1 step
  • Access Panel
  • 1 step
  • Hard Drive
  • 1 step
  • RAM
  • 1 step
  • Keyboard
  • 2 steps
  • Palmrest
  • 2 steps
  • Motherboard
  • 2 steps
  • Speaker
  • 1 step

Flags

1

Scenic Route

This guide’s procedure isn’t the most efficient way to get the job done, but still may be useful in some circumstances.

  • BackDell Inspiron 17R-5737

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Make sure the laptop is off before attempting to remove the battery.
  • Flip over your laptop so that the battery faces you.

Make sure the laptop is off before attempting to remove the battery.

Flip over your laptop so that the battery faces you.

1024

Step 2

  • Slide each latch away from the battery to unlock it.

Slide each latch away from the battery to unlock it.

Step 3

  • Lift the battery upwards to remove it.
  • Continue holding the latches when removing the battery.

Lift the battery upwards to remove it.

Continue holding the latches when removing the battery.

Step 4

              Optical Drive
  • Remove one 4.8mm screw with a JIS #00 screwdriver.
  • Remove the optical drive.

Remove one 4.8mm screw with a JIS #00 screwdriver.

Remove the optical drive.

Step 5

              Access Panel
  • Remove two 4.8mm screws with a JIS #00 screwdriver.
  • Remove the access panel.

Remove two 4.8mm screws with a JIS #00 screwdriver.

Remove the access panel.

Step 6

              Hard Drive
  • Remove three 4.8mm screws from the hard drive with a JIS #00 screwdriver.
  • Slide the hard drive to the left.
  • Slide the hard drive to the right and up.

Remove three 4.8mm screws from the hard drive with a JIS #00 screwdriver.

Slide the hard drive to the left.

Slide the hard drive to the right and up.

Step 7

              RAM
  • Slide the two clips away from the RAM.
  • Lift the RAM out.

Slide the two clips away from the RAM.

Lift the RAM out.

Step 8

              Keyboard
  • A metal spudger can scratch delicate internal parts. Be extra careful when removing the keyboard.
  • Use a metal spudger to loosen the main frame of the keyboard.
  • A metal spudger should be used instead of a plastic one because a plastic one will probably break.
  • Make sure to get the spudger under the entire keyboard and not just under the keys.

A metal spudger can scratch delicate internal parts. Be extra careful when removing the keyboard.

Use a metal spudger to loosen the main frame of the keyboard.

A metal spudger should be used instead of a plastic one because a plastic one will probably break.

Make sure to get the spudger under the entire keyboard and not just under the keys.

Step 9

  • Slowly lift the keyboard.
  • Lift the locking flap that holds the ribbon cable in place.
  • The white line on this ribbon cable marks the edge of the connection area. To reinstall, insert the cable into the connector up to this line, and then close the locking flap.
  • Remove the keyboard.

Slowly lift the keyboard.

Lift the locking flap that holds the ribbon cable in place.

The white line on this ribbon cable marks the edge of the connection area. To reinstall, insert the cable into the connector up to this line, and then close the locking flap.

Remove the keyboard.

Step 10

              Palmrest
  • Remove two 1.6mm screws from beneath the optical drive with a JIS #00 screwdriver.
  • Remove the nine remaining 4.8mm screws from the back of the computer with a JIS #00 screwdriver.

Remove two 1.6mm screws from beneath the optical drive with a JIS #00 screwdriver.

Remove the nine remaining 4.8mm screws from the back of the computer with a JIS #00 screwdriver.

Step 11

  • Remove the two exposed ribbon cables.
  • Remove the palmrest.

Remove the two exposed ribbon cables.

Remove the palmrest.

Step 12

              Motherboard
  • Remove the Wi-Fi chip by pulling upwards.

Remove the Wi-Fi chip by pulling upwards.

Step 13

  • Remove six 4.8mm screws with a JIS #00 screwdriver.
  • Remove two 3.2mm screws with aJIS #00 screwdriver.
  • Disconnect three cables from the front of the motherboard.
  • Slowly lift the motherboard exposing the bottom side.
  • Remove the ribbon cable from the back of the motherboard.
  • Remove the motherboard.

Remove six 4.8mm screws with a JIS #00 screwdriver.

Remove two 3.2mm screws with aJIS #00 screwdriver.

Disconnect three cables from the front of the motherboard.

Slowly lift the motherboard exposing the bottom side.

Remove the ribbon cable from the back of the motherboard.

Remove the motherboard.

Step 14

              Speaker
  • These screws strip easily.
  • Remove two 1.6mm screws on each speaker with a JIS #00 screwdriver.
  • Remove the speakers.

These screws strip easily.

Remove two 1.6mm screws on each speaker with a JIS #00 screwdriver.

Remove the speakers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    David Callahan

Member since: 10/19/2017

559 Reputation

                                      5 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       UMass Dartmouth, Team S3-G7, Bailey Fall 2017                        

                                                  Member of UMass Dartmouth, Team S3-G7, Bailey Fall 2017 



                    UMASSD-BAILEY-F17S3G7                     


                                            3 Members                     


                                            11 Guides authored