Difficulty

Moderate

Steps

8

Time Required

                          10 minutes

Sections

4

  • Battery
  • 1 step
  • Hinge Plate Cover
  • 1 step
  • Keyboard
  • 1 step
  • Display Assembly
  • 5 steps

Flags

0

  • BackDell Inspiron 1721

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Before starting the removal process, make sure the device is completely turned off.

What you need

Step 1

              Battery
  • Slide tabs outward to undo the locks.
  • Grab and pull the battery away from the device to remove.

Slide tabs outward to undo the locks.

Grab and pull the battery away from the device to remove.

1024

Step 2

              Hinge Plate Cover
  • Pry up on the corner of the hinge cover with an iFixit opening tool.
  • Use the iFixit opening tool along both sides and the front of the hinge cover to release it.
  • Lean the display back as far as it goes and lift up on the hinge cover to remove.

Pry up on the corner of the hinge cover with an iFixit opening tool.

Use the iFixit opening tool along both sides and the front of the hinge cover to release it.

Lean the display back as far as it goes and lift up on the hinge cover to remove.

Step 3

              Keyboard
  • Remove four 3mm Phillips #1 screws from the top of the keyboard.
  • Use an iFixit opening tool to slide the keyboard upwards toward the display.
  • Slide the keyboard until it is clear of the lock tab, and lift it up to remove.

Remove four 3mm Phillips #1 screws from the top of the keyboard.

Use an iFixit opening tool to slide the keyboard upwards toward the display.

Slide the keyboard until it is clear of the lock tab, and lift it up to remove.

Step 4

              Display Assembly
  • Loosen the two captive Phillips #0 screws.
  • Remove the cover.

Loosen the two captive Phillips #0 screws.

Remove the cover.

Step 5

  • Disconnect the antenna connectors from the WLAN card.

Disconnect the antenna connectors from the WLAN card.

Step 6

  • Remove the 3mm Phillips #0 screw securing the connector to the case ground.
  • Disconnect the display connector.
  • Disconnect the second connector, then remove the cable from the base.

Remove the 3mm Phillips #0 screw securing the connector to the case ground.

Disconnect the display connector.

Disconnect the second connector, then remove the cable from the base.

Step 7

  • Remove the display cable from the palm rest.
  • Use a spudger to carefully pull the antenna wires through to front of the device.

Remove the display cable from the palm rest.

Use a spudger to carefully pull the antenna wires through to front of the device.

Step 8

  • Remove the two 3.5 mm Phillips screws that hold the display assembly in place.
  • Lift the assembly straight up to separate it from the body of the device.

Remove the two 3.5 mm Phillips screws that hold the display assembly in place.

Lift the assembly straight up to separate it from the body of the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Jason Haddox

Member since: 09/04/2019

424 Reputation

                                      4 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Embry-Riddle Aeronautical University, Team S8-G5, Salas Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S8-G5, Salas Fall 2019 



                    ERAU-SALAS-F19S8G5                     


                                            4 Members                     


                                            9 Guides authored