Difficulty

Moderate

Steps

17

Time Required

                          5 minutes

Sections

5

  • Base Cover
  • 4 steps
  • Wireless Card (NIC)
  • 1 step
  • Fan
  • 4 steps
  • Heatsink
  • 2 steps
  • Display Assembly
  • 6 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackDell Inspiron 17" 7786 2-in-1

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Replacement of this assembly is fairly simple, though must be handled with care.

It is possible to replace components of the display assembly itself, however, it is a task that should be sought after by those who have the correct tools to replace such components.

What you need

Step 1

              Base Cover
  • Remove the eight M2 5mm screws that secure the base cover using a Phillips #0 screwdriver.

Remove the eight M2 5mm screws that secure the base cover using a Phillips #0 screwdriver.

1024

Step 2

  • Loosen the three captive screws that secure the base closer to the hinges.
  • Do not attempt to remove the three captive screws! You need only to loosen them. They’re supposed to stay on the base cover.

Loosen the three captive screws that secure the base closer to the hinges.

Do not attempt to remove the three captive screws! You need only to loosen them. They’re supposed to stay on the base cover.

Step 3

  • Carefully pry the base cover using an iFixit opening tool in the crevice near the hinges. Guide the pick along the edges and slightly lift upwards as you go along.
  • Do not start from the speaker end of the edges when opening, or you may cause further damage to your device!

Carefully pry the base cover using an iFixit opening tool in the crevice near the hinges. Guide the pick along the edges and slightly lift upwards as you go along.

Do not start from the speaker end of the edges when opening, or you may cause further damage to your device!

Step 4

  • Carefully remove the base cover from the laptop.

Carefully remove the base cover from the laptop.

Step 5

              Wireless Card (NIC)
  • Remove the screw holding down the small bracket for the wireless card using a Phillips #0 screwdriver.
  • Remove the black wired connection from the port over the black triangle.
  • Remove the wire with the white marking from the port above the white triangle.
  • Pull the Wi-Fi card out of its slot.

Remove the screw holding down the small bracket for the wireless card using a Phillips #0 screwdriver.

Remove the black wired connection from the port over the black triangle.

Remove the wire with the white marking from the port above the white triangle.

Pull the Wi-Fi card out of its slot.

Step 6

              Fan
  • Gently remove the I/O cable.

Gently remove the I/O cable.

Step 7

  • Remove the fan cable from the motherboard.

Remove the fan cable from the motherboard.

Step 8

  • Remove two 3 mm screws that secure the fan using a Phillips #0 screwdriver.

Remove two 3 mm screws that secure the fan using a Phillips #0 screwdriver.

Step 9

  • There is a little piece of tape/sticker on the fan that connects it to the heat sink. Gently remove this.
  • Lift the fan off the palm rest assembly.

There is a little piece of tape/sticker on the fan that connects it to the heat sink. Gently remove this.

Lift the fan off the palm rest assembly.

Step 10

              Heatsink
  • Loosen seven 3 mm captive screws securing the heatsink to the motherboard using a Phillips #0 screwdriver.

Loosen seven 3 mm captive screws securing the heatsink to the motherboard using a Phillips #0 screwdriver.

Step 11

  • Lift the heatsink off the motherboard.

Lift the heatsink off the motherboard.

Step 12

              Display Assembly
  • Ensure that you have your device opened flat at a 180 degree angle. This will make removal easier.

Ensure that you have your device opened flat at a 180 degree angle. This will make removal easier.

Step 13

  • Locate the ribbon cables for the assembly on the right hand side marked “MB1” and “MB2.”
  • The “MB1” ribbon is locked with a copper/brass colored handle that must be lifted upwards. Then you can remove the ribbon by pulling it away from the socket.
  • The “MB2” ribbon is locked in its socket with a black latch. Using a non-metallic precision tool (such as tweezers) lift the latch and pull away the MB2 cable.

Locate the ribbon cables for the assembly on the right hand side marked “MB1” and “MB2.”

The “MB1” ribbon is locked with a copper/brass colored handle that must be lifted upwards. Then you can remove the ribbon by pulling it away from the socket.

The “MB2” ribbon is locked in its socket with a black latch. Using a non-metallic precision tool (such as tweezers) lift the latch and pull away the MB2 cable.

Step 14

  • Remove the two screws holding down the assembly on the right hand area using a Phillips #00 screwdriver.

Remove the two screws holding down the assembly on the right hand area using a Phillips #00 screwdriver.

Step 15

  • Remove the screw protecting the endpoints of the NIC cables and NIC chip using a Phillips #0 screwdriver.
  • Gently pull away the cabling from the NIC chip.
  • The wires can be removed without removing the heat sink, though this is not advised if you are not familiar with the layout.

Remove the screw protecting the endpoints of the NIC cables and NIC chip using a Phillips #0 screwdriver.

Gently pull away the cabling from the NIC chip.

The wires can be removed without removing the heat sink, though this is not advised if you are not familiar with the layout.

Step 16

  • Remove the two screws holding down the bracket of the assembly on the left hand side using a Phillips #0 screwdriver.

Remove the two screws holding down the bracket of the assembly on the left hand side using a Phillips #0 screwdriver.

Step 17

  • Lift the display assembly upwards away from the palm/main assembly.

Lift the display assembly upwards away from the palm/main assembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Antonio Franco

Member since: 08/25/2022

977 Reputation

                                      10 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Gateway, Team 1-3, Class Fall 2022                        

                                                  Member of Gateway, Team 1-3, Class Fall 2022 



                    GCC-CLASS-F22S1G3                     


                                            4 Members                     


                                            15 Guides authored