Dell Inspiron 17 5755 Display Panel Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 minutes - 1 hour

Sections

Battery
3 steps
Keyboard
6 steps
Motherboard
22 steps
Display Panel
8 steps

Flags

BackDell Inspiron 17-5755
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Make sure the computer has been shut down, and isn’t plugged into an outlet before attempting to remove the battery.

Make sure the computer has been shut down, and isn’t plugged into an outlet before attempting to remove the battery.

1024

Step 2

Find the battery release latch on the bottom side of the computer.
Slide the latch to the left until you hear a “click”. This indicates that the battery has been released.

Find the battery release latch on the bottom side of the computer.

Slide the latch to the left until you hear a “click”. This indicates that the battery has been released.

Step 3

Safely remove the battery from the laptop.

Safely remove the battery from the laptop.

Step 4

              Keyboard

Open the display of the laptop as far as possible, and locate the tabs which secure the keyboard to the laptop.

Open the display of the laptop as far as possible, and locate the tabs which secure the keyboard to the laptop.

Step 5

Use a plastic opening tool to gently release the tabs that secure the keyboard to the laptop.

Use a plastic opening tool to gently release the tabs that secure the keyboard to the laptop.

Step 6

Carefully lift the keyboard from the laptop, being mindful of any attachments that it may have.

Carefully lift the keyboard from the laptop, being mindful of any attachments that it may have.

Step 7

Lift the zero insertion force (ZIF) tab that secures the keyboard back light ribbon cable
Afterwards, carefully detach the backlight cable from the laptop.

Lift the zero insertion force (ZIF) tab that secures the keyboard back light ribbon cable

Afterwards, carefully detach the backlight cable from the laptop.

Step 8

Gently release the ZIF tab that secures the keyboard ribbon cable to the laptop.
Afterwards, carefully slide the cable out of its slot.

Gently release the ZIF tab that secures the keyboard ribbon cable to the laptop.

Afterwards, carefully slide the cable out of its slot.

Step 9

Now that the keyboard is detached from the laptop, you may safely remove it.

Now that the keyboard is detached from the laptop, you may safely remove it.

Step 10

              Motherboard

Use a Phillips #0 screwdriver to unscrew the two 8mm screws which secure the base cover.

Use a Phillips #0 screwdriver to unscrew the two 8mm screws which secure the base cover.

Step 11

Locate the tabs that hold the base cover to the laptop and use a plastic opening tool to gently release the base cover.

Locate the tabs that hold the base cover to the laptop and use a plastic opening tool to gently release the base cover.

Step 12

Now with the base cover removed, you may lift it off of the laptop and continue.

Now with the base cover removed, you may lift it off of the laptop and continue.

Step 13

Disconnect the hard drive ribbon cable from the laptop by lifting the latch which secures it.

Disconnect the hard drive ribbon cable from the laptop by lifting the latch which secures it.

Step 14

Use a Phillips #0 screwdriver to remove the four 8mm screws which secure the hard drive assembly to the laptop.

Use a Phillips #0 screwdriver to remove the four 8mm screws which secure the hard drive assembly to the laptop.

Step 15

Carefully remove the hard drive and its assembly from the laptop.

Carefully remove the hard drive and its assembly from the laptop.

Step 16

Remove the 3mm screw which secures the wireless card bracket.
After removing the screw, remove the wireless card bracket, along with the antenna cables secured to the wireless card.
Afterwards, you may slide and remove the wireless card from the motherboard.

Remove the 3mm screw which secures the wireless card bracket.

After removing the screw, remove the wireless card bracket, along with the antenna cables secured to the wireless card.

Afterwards, you may slide and remove the wireless card from the motherboard.

Step 17

Gently spread apart the securing clips on each end of the memory-module slot until the memory module pops out.
Slide and remove the memory module afterwards.

Gently spread apart the securing clips on each end of the memory-module slot until the memory module pops out.

Slide and remove the memory module afterwards.

Step 18

Use a plastic opening tool to gently pry the CMOS battery found at the bottom right of the laptop out of the socket.

Use a plastic opening tool to gently pry the CMOS battery found at the bottom right of the laptop out of the socket.

Step 19

Use a Phillips #0 screwdriver to remove the 3mm screw which secures the optical-drive assembly to the computer base
Turn the computer over and using a plastic opening tool, push the optical-drive assembly out of the optical drive bay.
Afterwards, safely pull the optical-drive assembly out of the optical-drive bay.

Use a Phillips #0 screwdriver to remove the 3mm screw which secures the optical-drive assembly to the computer base

Turn the computer over and using a plastic opening tool, push the optical-drive assembly out of the optical drive bay.

Afterwards, safely pull the optical-drive assembly out of the optical-drive bay.

Step 20

Turn the computer over
Lift the latch securing the optical drive ribbon cable, and disconnect it from the motherboard.
Afterwards, use a Phillips #0 screwdriver to remove the four 5mm screws.

Turn the computer over

Lift the latch securing the optical drive ribbon cable, and disconnect it from the motherboard.

Afterwards, use a Phillips #0 screwdriver to remove the four 5mm screws.

Step 21

Turn over the laptop, and safely disconnect the speaker cable.

Turn over the laptop, and safely disconnect the speaker cable.

Step 22

Remove the antenna cables from the routing guides on the computer base.

Remove the antenna cables from the routing guides on the computer base.

Step 23

Use a Phillips #0 screwdriver to remove the 15 screws that secure the computer base to the palm rest assembly.
Afterwards, safely pry the computer base from the palm rest assembly using a plastic opening tool.
There are 3 different screws used: Three 2mm screws on the edge of the optical drive, two 3mm screws located where the battery was, and ten 8mm screws.

Use a Phillips #0 screwdriver to remove the 15 screws that secure the computer base to the palm rest assembly.

Afterwards, safely pry the computer base from the palm rest assembly using a plastic opening tool.

There are 3 different screws used: Three 2mm screws on the edge of the optical drive, two 3mm screws located where the battery was, and ten 8mm screws.

Step 24

Use a Phillips #0 screwdriver to remove the 5mm screw that secures the I/O board to the palm-rest assembly.

Use a Phillips #0 screwdriver to remove the 5mm screw that secures the I/O board to the palm-rest assembly.

Step 25

Lift the I/O board and turn it over.
Afterwards, lift the ZIF latch and disconnect the I/O-board cable from the I/O board.

Lift the I/O board and turn it over.

Afterwards, lift the ZIF latch and disconnect the I/O-board cable from the I/O board.

Step 26

Disconnect the fan cable from the motherboard.
Use a Phillips #0 screwdriver to remove the heat-sink screws in sequential order, as indicated by the numbers on the heat-sink assembly.
Afterwards lift the heat-sink assembly off the motherboard.

Disconnect the fan cable from the motherboard.

Use a Phillips #0 screwdriver to remove the heat-sink screws in sequential order, as indicated by the numbers on the heat-sink assembly.

Afterwards lift the heat-sink assembly off the motherboard.

Step 27

Turn the computer over and open the display as far as possible.
Lift the latches for the power button board cable and disconnect it along with the touchpad cable from the motherboard.

Turn the computer over and open the display as far as possible.

Lift the latches for the power button board cable and disconnect it along with the touchpad cable from the motherboard.

Step 28

Close the display and turn the computer over.
Proceed to lift the latch which secures the ZIF display cable to the motherboard.
Disconnect the display cable from the motherboard.

Close the display and turn the computer over.

Proceed to lift the latch which secures the ZIF display cable to the motherboard.

Disconnect the display cable from the motherboard.

Step 29

Use a Phillips# 0 screwdriver to remove the 3mm screw that secures the motherboard to the palm-rest assembly.
Afterwards, carefully peel the I/O board cable off the palm-rest assembly.

Use a Phillips# 0 screwdriver to remove the 3mm screw that secures the motherboard to the palm-rest assembly.

Afterwards, carefully peel the I/O board cable off the palm-rest assembly.

Step 30

Turn the motherboard over.
Lift the latch to disconnect the I/O-board cable from the motherboard.

Turn the motherboard over.

Lift the latch to disconnect the I/O-board cable from the motherboard.

Step 31

Disconnect the power-adapter port cable from the motherboard.
Afterwards you may safely remove the motherboard from the laptop.

Disconnect the power-adapter port cable from the motherboard.

Afterwards you may safely remove the motherboard from the laptop.

Step 32

              Display Panel

Using a Phillips 0 screwdriver, remove the screw (M2 x 3) the power-adapter port to the palm-rest assembly.
Peel off the tape that secures the power-adapter port to the palm-rest assembly.

Using a Phillips 0 screwdriver, remove the screw (M2 x 3) the power-adapter port to the palm-rest assembly.

Peel off the tape that secures the power-adapter port to the palm-rest assembly.

Step 33

Carefully detach the antenna cables from their respective routing guides

Carefully detach the antenna cables from their respective routing guides

Step 34

Using a Phillips 0 screwdriver, remove the 7 screws (M2.5 x 5) that secure the display hinges to the palm-rest assembly.
Detach the display assembly from the palm rest assembly

Using a Phillips 0 screwdriver, remove the 7 screws (M2.5 x 5) that secure the display hinges to the palm-rest assembly.

Detach the display assembly from the palm rest assembly

Step 35

Using the tip of your fingers, gently pry off the display bezel from the back-cover

Using the tip of your fingers, gently pry off the display bezel from the back-cover

Step 36

Using a Phillips 0 screwdriver, remove the 10 screws (M2.5 x 4.5) that secure the display panel to the display back-cover.

Using a Phillips 0 screwdriver, remove the 10 screws (M2.5 x 4.5) that secure the display panel to the display back-cover.

Step 37

Using a Phillips 0 screwdriver, remove the 6 screws (M2 x 3) that secure the display hinges to the display panel.

Using a Phillips 0 screwdriver, remove the 6 screws (M2 x 3) that secure the display hinges to the display panel.

Step 38

Carefully turn the display assembly around.
Gently peel the display cable and disconnect the latch that is found under it.

Carefully turn the display assembly around.

Gently peel the display cable and disconnect the latch that is found under it.

Step 39

Once the display hinges are removed, your display panel is now ready to be replaced.

Once the display hinges are removed, your display panel is now ready to be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Jeff

Member since: 02/15/2017

376 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       USF Tampa, Team S6-G1, Lacy Spring 2017                        

                                                  Member of USF Tampa, Team S6-G1, Lacy Spring 2017 



                    USFT-LACY-S17S6G1                     


                                            3 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team