Dell Inspiron 15 Gaming 7567 Display Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 35 minutes

Sections

Display Assembly
25 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackDell Inspiron 15 Gaming 7567
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Disconnect the Camera Cable

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
Using the pull-tab, disconnect the camera cable from the system board.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Using the pull-tab, disconnect the camera cable from the system board.

1024

Step 2

              Peeling the Camera Cable

Peel off the camera cable from the computer base.

Peel off the camera cable from the computer base.

Step 3

              Note the Routing

Note the antenna cables routing and remove the antenna cables from the routing guides on the computer base.

Note the antenna cables routing and remove the antenna cables from the routing guides on the computer base.

Step 4

              Remove the Screw

Remove the screw (M3x3) that secures the display-cable bracket to the system board.

Remove the screw (M3x3) that secures the display-cable bracket to the system board.

Step 5

              Lifting the Display Cable

Lift the display-cable bracket off the computer base.

Lift the display-cable bracket off the computer base.

Step 6

              Disconnecting the Display Cable

Using the pull tab, disconnect the display cable from the system board.

Using the pull tab, disconnect the display cable from the system board.

Step 7

              Remove the Display Cable

Remove the display cable from the routing guides on the computer base and peel off the display cable from the computer base.

Remove the display cable from the routing guides on the computer base and peel off the display cable from the computer base.

Step 8

              Remove the Screws

Remove the two screws (M2x3) that secure the display assembly to the computer base.

Remove the two screws (M2x3) that secure the display assembly to the computer base.

Step 9

              Remove the Screws

Remove the two screws (M2.5x5) that secure the display assembly to the computer base.

Remove the two screws (M2.5x5) that secure the display assembly to the computer base.

Step 10

              Open the Display

Turn the computer over and open the display.

Turn the computer over and open the display.

Step 11

              Remove the Screws

Step 12

              Lifting the Display Assembly

Lift the display assembly off the computer base.

Lift the display assembly off the computer base.

Step 13

              Align the Screw Holes

Align the screw holes on the NEW display assembly with the screw holes on the computer base.

Align the screw holes on the NEW display assembly with the screw holes on the computer base.

Step 14

              Replace the Screws

Replace the two screws (M2x2.5) that secure the display assembly to the computer base.

Replace the two screws (M2x2.5) that secure the display assembly to the computer base.

Step 15

              Close the Display

Close the display and turn the computer over.

Close the display and turn the computer over.

Step 16

              Replace the Screws

Replace the two screws (M2x3) that secure the display assembly to the computer base.

Replace the two screws (M2x3) that secure the display assembly to the computer base.

Step 17

              Replace the Screws

Replace the two screws (M2.5x5) that secure the display assembly to the computer base.

Replace the two screws (M2.5x5) that secure the display assembly to the computer base.

Step 18

              Route the Display Cable

Route the display cable through the routing guides on the computer base.

Route the display cable through the routing guides on the computer base.

Step 19

              Adhering the Display Cable

Adhere the display cable and the camera cable to the computer base.

Adhere the display cable and the camera cable to the computer base.

Step 20

              Connect the Display Cable

Connect the display cable to the system board.

Connect the display cable to the system board.

Step 21

              Align the Screw Hole

Align the screw hole on display-cable bracket with the screw hole on the computer base.

Align the screw hole on display-cable bracket with the screw hole on the computer base.

Step 22

              Replace the Screw

Replace the screw (M3x3) that secures the display-cable bracket to the computer base.

Replace the screw (M3x3) that secures the display-cable bracket to the computer base.

Step 23

              Route the Antenna Cables

Route the antenna cables through the routing guides on the computer base.

Route the antenna cables through the routing guides on the computer base.

Step 24

              Adhering the Camera Cable

Adhere the camera cable to the computer base.

Adhere the camera cable to the computer base.

Step 25

              Connecting the Camera Cable

Connect the camera cable to the system board.

Connect the camera cable to the system board.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor

                    Terrence15

Member since: 12/18/2017

78,526 Reputation

                                      441 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored

michael gunawan - Nov 22, 2018

i bought the version with the tn panel, is there a list of compatible ips panels for this particular model? thanks

Dereck Scott - Apr 4, 2019

Hello, I bought an IPS version around a year ago but in that time a number of things happened, The computer goes to sleep without the lid being down, so i changed the setting to “Do nothing” when i closed the lid. As you expect it did not help, insead of going to sleep the display goes black, Also my ASDFJKL keys dont work, they work somethimes but im typing on a wired keyboard because of it. I NEED HELP PLEASE HELP

Member-Contributed Guide#

Introduction#

What you need#

Team#

Member-Contributed Guide

Introduction

What you need

Team