Difficulty
Moderate
Steps
25
Time Required
15 - 40 minutes
Sections
1
- Display Assembly
- 25 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackDell Inspiron 15 Gaming 7566
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Disconnect the Camera Cable
- WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
- Using the pull-tab, disconnect the camera cable from the system board.
WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
Using the pull-tab, disconnect the camera cable from the system board.
1024
Step 2
Peeling the Camera Cable
- Peel off the camera cable from the computer base.
Peel off the camera cable from the computer base.
Step 3
Note the Antenna Cables
- Note the antenna cables routing and remove the antenna cables from the routing guides on the computer base.
Note the antenna cables routing and remove the antenna cables from the routing guides on the computer base.
Step 4
Remove the Screw
- Remove the screw (M3x3) that secures the display-cable bracket to the system board.
Remove the screw (M3x3) that secures the display-cable bracket to the system board.
Step 5
Lifting the Display Cable Bracket
- Lift the display-cable bracket off the computer base.
Lift the display-cable bracket off the computer base.
Step 6
Disconnect the Display Cable
- Using the pull tab, disconnect the display cable from the system board.
Using the pull tab, disconnect the display cable from the system board.
Step 7
Remove the Display Cable
- Remove the display cable from the routing guides on the computer base and peel off the display cable from the computer base.
Remove the display cable from the routing guides on the computer base and peel off the display cable from the computer base.
Step 8
Remove the Screws
- Remove the two screws (M2x3) that secure the display assembly to the computer base.
Remove the two screws (M2x3) that secure the display assembly to the computer base.
Step 9
Remove the Screws
- Remove the two screws (M2.5x5) that secure the display assembly to the computer base.
Remove the two screws (M2.5x5) that secure the display assembly to the computer base.
Step 10
Turn the Computer
- Turn the computer over and open the display.
Turn the computer over and open the display.
Step 11
Remove the Screws
Step 12
Lifting the Display Assembly
- Lift the display assembly off the computer base.
Lift the display assembly off the computer base.
Step 13
Align the Screw Holes
- Align the screw holes on the NEW display assembly with the screw holes on the computer base.
Align the screw holes on the NEW display assembly with the screw holes on the computer base.
Step 14
Replace the Screws
- Replace the two screws (M2x2.5) that secure the display assembly to the computer base.
Replace the two screws (M2x2.5) that secure the display assembly to the computer base.
Step 15
Close the Display
- Close the display and turn the computer over.
Close the display and turn the computer over.
Step 16
Replace the Screws
- Replace the two screws (M2x3) that secure the display assembly to the computer base.
Replace the two screws (M2x3) that secure the display assembly to the computer base.
Step 17
Replace the Screws
- Replace the two screws (M2.5x5) that secure the display assembly to the computer base.
Replace the two screws (M2.5x5) that secure the display assembly to the computer base.
Step 18
Route the Display Cable
- Route the display cable through the routing guides on the computer base.
Route the display cable through the routing guides on the computer base.
Step 19
Adhering the Display Cable
- Adhere the display cable and the camera cable to the computer base.
Adhere the display cable and the camera cable to the computer base.
Step 20
Connect the Display Cable
- Connect the display cable to the system board.
Connect the display cable to the system board.
Step 21
Align the Screw Hole
- Align the screw hole on display-cable bracket with the screw hole on the computer base.
Align the screw hole on display-cable bracket with the screw hole on the computer base.
Step 22
Replace the Screw
- Replace the screw (M3x3) that secures the display-cable bracket to the computer base.
Replace the screw (M3x3) that secures the display-cable bracket to the computer base.
Step 23
Route the Antenna Cables
- Route the antenna cables through the routing guides on the computer base.
Route the antenna cables through the routing guides on the computer base.
Step 24
Adhering the Camera Cable
- Adhere the camera cable to the computer base.
Adhere the camera cable to the computer base.
Step 25
Connect the Camera Cable
- Connect the camera cable to the system board.
Connect the camera cable to the system board.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Terrence15
Member since: 12/18/2017
78,526 Reputation
441 Guides authored
Badges:
28
+25 more badges
Team
Informative Technologies Inc.
Member of Informative Technologies Inc.
Community
38 Members
1,980 Guides authored
