Difficulty

Moderate

Steps

10

Time Required

                          20 - 35 minutes

Sections

4

  • Back Panel
  • 2 steps
  • Fan
  • 3 steps
  • SSD M.2 Drive
  • 2 steps
  • Motherboard
  • 3 steps

Flags

0

  • BackDell Inspiron 15 7579

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Panel
  • Remove the ten 7.9 mm screws with the Phillips PH0 screwdriver.

Remove the ten 7.9 mm screws with the Phillips PH0 screwdriver.

1024

Step 2

  • Insert metal spudger into a gap in between the back panel and the back of the screen.
  • Pry off the back panel using the metal spudger as a lever, and remove the back panel by lifting the rest off by hand.

Insert metal spudger into a gap in between the back panel and the back of the screen.

Pry off the back panel using the metal spudger as a lever, and remove the back panel by lifting the rest off by hand.

Step 3

              Fan
  • Remove the two 7.9 mm screws from the fan with a Phillips #0 screwdriver.

Remove the two 7.9 mm screws from the fan with a Phillips #0 screwdriver.

Step 4

  • Unplug the wires from the port.
  • Be sure to pull from the plastic connector, not the wires.

Unplug the wires from the port.

Be sure to pull from the plastic connector, not the wires.

Step 5

  • Carefully lift the fan out of the computer.

Carefully lift the fan out of the computer.

Step 6

              SSD M.2 Drive
  • Remove the single 3.6 mm screw holding the left side of the M.2 SSD card with a Phillips PH0 screwdriver.

Remove the single 3.6 mm screw holding the left side of the M.2 SSD card with a Phillips PH0 screwdriver.

Step 7

  • Gently pull out the SSD card at the angle it is relaxed in to remove it. It is easiest to do this by hand.
  • Be gentle when pulling the SSD card out. It should take little effort to get it to slide out properly.

Gently pull out the SSD card at the angle it is relaxed in to remove it. It is easiest to do this by hand.

Be gentle when pulling the SSD card out. It should take little effort to get it to slide out properly.

Step 8

              Motherboard
  • Remove the six 2.1 mm screws with the Phillips #0 screwdriver.

Remove the six 2.1 mm screws with the Phillips #0 screwdriver.

Step 9

  • Unplug the eight ribbon cables connected to the motherboard.

Unplug the eight ribbon cables connected to the motherboard.

Step 10

  • Lift the motherboard up from the side opposite of the external ports and remove it from the laptop.

Lift the motherboard up from the side opposite of the external ports and remove it from the laptop.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Musukula P McClain

Member since: 09/20/2021

97 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       The Citadel Military College of South Carolina, Team 2-11, Eggleston Fall 2021                        

                                                  Member of The Citadel Military College of South Carolina, Team 2-11, Eggleston Fall 2021 



                    CMCSC-EGGLESTON-F21S2G11                     


                                            3 Members                     


                                            3 Guides authored