Dell Inspiron 15 5558 Display Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

13

Time Required

                          6 - 15 minutes            

Sections

1

• Display Assembly
• 13 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackDell Inspiron 15-5558

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Note the Antenna Cable               

• WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
• Note the antenna cable routing and remove the cable from its routing guides.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Note the antenna cable routing and remove the cable from its routing guides.

1024

Step 2

              Disconnecting the Display Cable               

• Lift the latch and disconnect the display cable from the system board.

Lift the latch and disconnect the display cable from the system board.

Step 3

              Note the Display Cable               

• Note the display cable routing and remove the cable from its routing guides.

Note the display cable routing and remove the cable from its routing guides.

Step 4

              Turn the Computer Over               

• Turn the computer over.
• Open the display at an angle of 90 degrees.

Turn the computer over.

Open the display at an angle of 90 degrees.

Step 5

              Placing the Computer               

• Place the computer on the edge of the table so that the palm-rest assembly is on the table and the display assembly extends past the table edge with the display hinges facing up.

Place the computer on the edge of the table so that the palm-rest assembly is on the table and the display assembly extends past the table edge with the display hinges facing up.

Step 6

              Remove the Screws               

• Remove the screws that secure the display hinges to the palm-rest assembly.

Remove the screws that secure the display hinges to the palm-rest assembly.

Step 7

              Lifting the Display Assembly               

• Lift the display assembly off the palm-rest assembly.

Lift the display assembly off the palm-rest assembly.

Step 8

              Placing the Palm Rest Assembly               

• Place the palm-rest assembly at the edge of the table with the coin-cell battery facing away from the edge.

Place the palm-rest assembly at the edge of the table with the coin-cell battery facing away from the edge.

Step 9

              Align the Screw Holes               

• Align the screw holes on the display hinges with the screw holes on the palm-rest assembly.

Align the screw holes on the display hinges with the screw holes on the palm-rest assembly.

Step 10

              Replace the Screws               

• Replace the screws that secure the display hinges to the palm-rest assembly.

Replace the screws that secure the display hinges to the palm-rest assembly.

Step 11

              Route the Display Cable               

• Close the display and turn the computer over.
• Route the display cable through the routing guides on the palm-rest assembly.

Close the display and turn the computer over.

Route the display cable through the routing guides on the palm-rest assembly.

Step 12

              Slide the Display Cable               

• Slide the display cable to the connector and press down on the latch to connect the display cable to the system board.

Slide the display cable to the connector and press down on the latch to connect the display cable to the system board.

Step 13

              Routing the Antenna Cable               

• Route the antenna cable through the routing guides on the palm-rest assembly.

Route the antenna cable through the routing guides on the palm-rest assembly.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    Terrence15                     

Member since: 12/18/2017

78,526 Reputation

                                      441 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges                           

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored