Difficulty

Moderate

Steps

17

Time Required

                          6 - 15 minutes

Sections

1

  • Display Assembly
  • 17 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackDell Inspiron 15 3565

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove the Screws
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Remove the three screws (2.5x8) that secure the display hinges to the palm-rest assembly.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Remove the three screws (2.5x8) that secure the display hinges to the palm-rest assembly.

1024

Step 2

              Open the Display Hinges
  • Open the display hinges to an angle of 90 degrees.

Open the display hinges to an angle of 90 degrees.

Step 3

              Peeling the Tape
  • Peel the tape that secures the display cable to the palm-rest assembly.

Peel the tape that secures the display cable to the palm-rest assembly.

Step 4

              Open the Latch
  • Open the latch and disconnect the display cable.

Open the latch and disconnect the display cable.

Step 5

              Open the Latch

Step 6

              Note the Routing
  • Note the display cable routing and remove the display cable from the routing guides on the palm-rest assembly.

Note the display cable routing and remove the display cable from the routing guides on the palm-rest assembly.

Step 7

              Note the Antenna Cable
  • Note the antenna cable routing and remove the cable from its routing guides on the palm-rest assembly.

Note the antenna cable routing and remove the cable from its routing guides on the palm-rest assembly.

Step 8

              Open the Palm-Rest Assembly
  • Open the palm-rest assembly at an angle and slide it off the display assembly.

Open the palm-rest assembly at an angle and slide it off the display assembly.

Step 9

              Placing the Display Assembly
  • Place the NEW display assembly on a clean, flat surface.

Place the NEW display assembly on a clean, flat surface.

Step 10

              Placing the Palm-Rest Assembly
  • Place the palm-rest assembly on the display assembly.

Place the palm-rest assembly on the display assembly.

Step 11

              Close the Hinges
  • Close the display hinges and align the screw holes on the display hinges with the screw holes on the palm-rest assembly.

Close the display hinges and align the screw holes on the display hinges with the screw holes on the palm-rest assembly.

Step 12

              Replace the Screws
  • Replace the three screws (2.5x8) that secure the display hinges to the palm-rest assembly.

Replace the three screws (2.5x8) that secure the display hinges to the palm-rest assembly.

Step 13

              Routing the Antenna Cables
  • Route the antenna cables through the routing guides on the palm-rest assembly.

Route the antenna cables through the routing guides on the palm-rest assembly.

Step 14

              Connecting the Display Cable
  • Connect the display cable and close the latch to secure the cable.

Connect the display cable and close the latch to secure the cable.

Step 15

              Route the Display Cable
  • Route the display cable through the routing guides on the palm-rest assembly

Route the display cable through the routing guides on the palm-rest assembly

Step 16

              Adhering the Tape
  • Adhere the tape that secures the display cable to the palm-rest assembly.

Adhere the tape that secures the display cable to the palm-rest assembly.

Step 17

              Close the Display
  • Close the display and turn the computer over.

Close the display and turn the computer over.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Terrence15

Member since: 12/18/2017

78,526 Reputation

                                      441 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored