Dell Inspiron 1464 Display Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

13

Time Required

                          5 - 25 minutes            

Sections

1

• Display Assembly
• 13 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackDell Inspiron 1464

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Note the Routing               

• WARNING: Before working inside your computer, read the safety information that shipped with your computer. Follow the procedures in Before You Begin.
• CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface.
• Note the routing of the Mini-Card antenna cables and remove them from the routing guides on the bottom of the computer.

WARNING: Before working inside your computer, read the safety information that shipped with your computer. Follow the procedures in Before You Begin.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface.

Note the routing of the Mini-Card antenna cables and remove them from the routing guides on the bottom of the computer.

1024

Step 2

              Remove the Screws               

• Remove the two screws on the bottom of the computer that secure the display assembly to the computer base.

Remove the two screws on the bottom of the computer that secure the display assembly to the computer base.

Step 3

              Pull the Cables Up               

• Pull the Mini-Card antenna cables up through the slot in the computer base.

Pull the Mini-Card antenna cables up through the slot in the computer base.

Step 4

              Note the Routing               

• Note the routing of the Mini-Card antenna cables and remove them from the routing guides on the palm rest.

Note the routing of the Mini-Card antenna cables and remove them from the routing guides on the palm rest.

Step 5

              Disconnect the Display Cable               

• Disconnect the display cable from the connector on the system board and remove the display cable grounding screw.

Disconnect the display cable from the connector on the system board and remove the display cable grounding screw.

Step 6

              Remove the Screws               

• Remove the three screws that secure the display assembly to the computer base.

Remove the three screws that secure the display assembly to the computer base.

Step 7

              Removing the Display Assembly               

• Lift the display assembly off the alignment posts on the computer base.

Lift the display assembly off the alignment posts on the computer base.

Step 8

              Placing the Display Assembly               

• Use the alignment posts to place the NEW display assembly on the computer base.

Use the alignment posts to place the NEW display assembly on the computer base.

Step 9

              Replace the Screws               

• Replace the three screws that secure the display assembly to the computer base.

Replace the three screws that secure the display assembly to the computer base.

Step 10

              Connecting the Display Cable               

• Connect the display cable to the connector on the system board and replace the display cable grounding screw.

Connect the display cable to the connector on the system board and replace the display cable grounding screw.

Step 11

              Routing the Cables               

• Route the Mini-Card antenna cables through the routing guides on the palm rest.

Route the Mini-Card antenna cables through the routing guides on the palm rest.

Step 12

              Thread the Cables               

• Thread the Mini-Card antenna cables through the slot in the computer base.

Thread the Mini-Card antenna cables through the slot in the computer base.

Step 13

              Replace the Screws               

• Turn the computer over and replace the two screws that secure the display assembly to the computer base.

Turn the computer over and replace the two screws that secure the display assembly to the computer base.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 

                    Terrence15                     

Member since: 12/18/2017

78,526 Reputation

                                      441 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges                           

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored