Difficulty

Easy

Steps

12

Time Required

                          6 - 15 minutes

Sections

1

  • Hard Drive
  • 12 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackDell Inspiron 14 Gaming 7467

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Disconnecting the Hard Drive Cable
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • CAUTION: Hard drives are fragile. Exercise care when handling the hard drive.
  • CAUTION: To avoid data loss, do not remove the hard drive while the computer is in sleep or on state.
  • CAUTION: The latch on the hard-drive locking connector is fragile. Pulling the latch forcefully may damage the hard-drive locking connector. Exercise care when handling the latch on the hard-drive locking connector.
  • Using a plastic scribe, lift the latch and use the pull tab to disconnect the hard-drive cable from the system board.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

CAUTION: Hard drives are fragile. Exercise care when handling the hard drive.

CAUTION: To avoid data loss, do not remove the hard drive while the computer is in sleep or on state.

CAUTION: The latch on the hard-drive locking connector is fragile. Pulling the latch forcefully may damage the hard-drive locking connector. Exercise care when handling the latch on the hard-drive locking connector.

Using a plastic scribe, lift the latch and use the pull tab to disconnect the hard-drive cable from the system board.

1024

Step 2

              Remove the Screws
  • Remove the four screws (M2.5x3 Ladder type) that secure the hard-drive assembly to the computer base.

Remove the four screws (M2.5x3 Ladder type) that secure the hard-drive assembly to the computer base.

Step 3

              Lifting the Assembly
  • Lift the hard-drive assembly, along with its cable, off the computer base.

Lift the hard-drive assembly, along with its cable, off the computer base.

Step 4

              Disconnect the Interposer
  • Disconnect the interposer from the hard-drive assembly.

Disconnect the interposer from the hard-drive assembly.

Step 5

              Remove the Screws
  • Remove the four screws (M3x3) that secure the hard-drive bracket to the hard drive.

Remove the four screws (M3x3) that secure the hard-drive bracket to the hard drive.

Step 6

              Remove the Hard-Drive Bracket
  • Remove the hard-drive bracket off the hard drive.

Remove the hard-drive bracket off the hard drive.

Step 7

              Align the Screw Holes
  • Align the screw holes on the hard drive-bracket with the screw holes on the NEW hard drive.

Align the screw holes on the hard drive-bracket with the screw holes on the NEW hard drive.

Step 8

              Replace the Screws
  • Replace the four screws (M3x3) that secure the hard-drive bracket to the hard drive.

Replace the four screws (M3x3) that secure the hard-drive bracket to the hard drive.

Step 9

              Connect the Interposer
  • Connect the interposer to the hard drive.

Connect the interposer to the hard drive.

Step 10

              Align the Screw Holes
  • Align the screw holes on the hard-drive assembly with the screw holes on the computer base.

Align the screw holes on the hard-drive assembly with the screw holes on the computer base.

Step 11

              Replace the Screws
  • Replace the four screws (M2.5x3 Ladder type) that secure the hard-drive assembly to the computer base.

Replace the four screws (M2.5x3 Ladder type) that secure the hard-drive assembly to the computer base.

Step 12

              Connect the Cable
  • Connect the hard-drive cable to the system board.

Connect the hard-drive cable to the system board.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Terrence15

Member since: 12/18/2017

78,526 Reputation

                                      441 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored