Dell Inspiron 14 Gaming 7467 Display Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 40 minutes

Sections

Display Assembly
19 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackDell Inspiron 14 Gaming 7467
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Disconnecting the Camera Cable

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
Using the pull-tab, disconnect the camera cable from the system board.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Using the pull-tab, disconnect the camera cable from the system board.

1024

Step 2

              Peel the Camera Cable

Peel off the camera cable from the computer base.

Peel off the camera cable from the computer base.

Step 3

              Remove the Screw

Remove the screw (M2x3) that secures the display-cable bracket to the system board.

Remove the screw (M2x3) that secures the display-cable bracket to the system board.

Step 4

              Removing the Cable Bracket

Lift the display-cable bracket off the system board.

Lift the display-cable bracket off the system board.

Step 5

              Disconnecting the Display Cable

Using the pull-tab, disconnect the display cable from the system board.

Using the pull-tab, disconnect the display cable from the system board.

Step 6

              Peeling the Display Cable

Peel off the display cable from the computer base.

Peel off the display cable from the computer base.

Step 7

              Remove the Screws

Remove the two screws (M2x3) that secure the display assembly to the computer base.

Remove the two screws (M2x3) that secure the display assembly to the computer base.

Step 8

              Remove the Screws

Remove the two screws (M2.5x5) that secure the display assembly to the computer base.

Remove the two screws (M2.5x5) that secure the display assembly to the computer base.

Step 9

              Remove the Screws

Turn the computer over and open the display.
Remove the two screws (M2.5x5) that secure the display assembly to the computer base.

Turn the computer over and open the display.

Step 10

              Lift the Display Assembly

Lift the display assembly off the computer base.

Lift the display assembly off the computer base.

Step 11

              Align the Screw Hole

Align the screw holes on the NEW display assembly with the screw holes on the computer base.

Align the screw holes on the NEW display assembly with the screw holes on the computer base.

Step 12

              Replace the Screws

Replace the two screws (M2.5x5) that secure the display assembly to the computer base.

Replace the two screws (M2.5x5) that secure the display assembly to the computer base.

Step 13

              Replace the Screws

Close the display and turn the computer over.
Replace the two screws (M2.5x5) that secure the display assembly to the computer base.

Close the display and turn the computer over.

Step 14

              Replace the Screws

Replace the two screws (M2x3) that secure the display assembly to the computer base.

Replace the two screws (M2x3) that secure the display assembly to the computer base.

Step 15

              Adhere the Cable

Adhere the display cable and the camera cable to the computer base.

Adhere the display cable and the camera cable to the computer base.

Step 16

              Route the Cables

Route the antenna cables through the routing guides on the computer base.

Route the antenna cables through the routing guides on the computer base.

Step 17

              Connect the Cable

Connect the display cable and camera cable to the system board.

Connect the display cable and camera cable to the system board.

Step 18

              Align the Screw Hole

Align the screw hole on the display-cable bracket with the screw hole on the system board.

Align the screw hole on the display-cable bracket with the screw hole on the system board.

Step 19

              Replace the Screw

Replace the screw (M2x3) that secures the display cable bracket to the system board.

Replace the screw (M2x3) that secures the display cable bracket to the system board.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Terrence15

Member since: 12/18/2017

78,526 Reputation

                                      441 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored

Member-Contributed Guide#

Introduction#

What you need#

Team#

Member-Contributed Guide

Introduction

What you need

Team