Dell Inspiron 14 Gaming 7466 Display Assembly Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          8 - 30 minutes

Sections

Display Assembly
20 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackDell Inspiron 14 Gaming 7466
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Disconnecting the Camera Cable

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
Using the pull-tab, disconnect the camera cable from the system board.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Using the pull-tab, disconnect the camera cable from the system board.

1024

Step 2

              Peeling the Camera Cable

Peel off the camera cable from the computer base.

Peel off the camera cable from the computer base.

Step 3

              Remove the Antenna Cables

Remove the antenna cables from the routing guides on the computer base.

Remove the antenna cables from the routing guides on the computer base.

Step 4

              Remove the Screw

Remove the screw (M2x3) that secures the display-cable bracket to the system board.

Remove the screw (M2x3) that secures the display-cable bracket to the system board.

Step 5

              Lifting the Display Cable Bracket

Lift the display-cable bracket off the system board.

Lift the display-cable bracket off the system board.

Step 6

              Disconnecting the Display Cable

Using the pull-tab, disconnect the display cable from the system board.

Using the pull-tab, disconnect the display cable from the system board.

Step 7

              Peel off the Display Cable

Peel off the display cable from the computer base.

Peel off the display cable from the computer base.

Step 8

              Remove the Screws

Remove the two screws (M2x3) that secure the display assembly to the computer base.

Remove the two screws (M2x3) that secure the display assembly to the computer base.

Step 9

              Remove the Screws

Remove the two screws (M2.5x5) that secure the display assembly to the computer base.

Remove the two screws (M2.5x5) that secure the display assembly to the computer base.

Step 10

              Open the Display

Turn the computer over and open the display.

Turn the computer over and open the display.

Step 11

              Remove the Screws

Step 12

              Lifting the Display Assembly

Lift the display assembly off the computer base.

Lift the display assembly off the computer base.

Step 13

              Align the Screw Holes

Align the screw holes on the NEW display assembly with the screw holes on the computer base.

Align the screw holes on the NEW display assembly with the screw holes on the computer base.

Step 14

              Replace the Screws

Replace the two screws (M2.5x5) that secure the display assembly to the computer base.

Replace the two screws (M2.5x5) that secure the display assembly to the computer base.

Step 15

              Replace the Screws

Close the display and turn the computer over.
Replace the two screws (M2.5x5) that secure the display assembly to the computer base.

Close the display and turn the computer over.

Step 16

              Replace the Screws

Replace the two screws (M2x3) that secure the display assembly to the computer base.

Replace the two screws (M2x3) that secure the display assembly to the computer base.

Step 17

              Adhering the Cables

Adhere the display cable and the camera cable to the computer base.

Adhere the display cable and the camera cable to the computer base.

Step 18

              Connect the Display Cable

Connect the display cable and camera cable to the system board.

Connect the display cable and camera cable to the system board.

Step 19

              Align the Screw Hole

Align the screw hole on the display-cable bracket with the screw hole on the system board.

Align the screw hole on the display-cable bracket with the screw hole on the system board.

Step 20

              Replace the Screw

Replace the screw (M2x3) that secures the display cable bracket to the system board.

Replace the screw (M2x3) that secures the display cable bracket to the system board.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Terrence15

Member since: 12/18/2017

78,526 Reputation

                                      441 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored

Member-Contributed Guide#

Introduction#

What you need#

Team#

Member-Contributed Guide

Introduction

What you need

Team