Difficulty
Moderate
Steps
8
Time Required
10 minutes
Sections
2
- Battery
- 3 steps
- Hinge
- 5 steps
Flags
In Progress
This guide is a work in progress. Reload periodically to see the latest changes!
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackDell Inspiron 13-7352
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Before you begin, be sure to turn off your laptop and unplug it from the outlet.
- Use a Phillips screwdriver to remove the ten 7.5mm screws that securing the back panel.
- Use the plastic opening tool to pry up and loosen the back panel.
- Remove the back panel.
Before you begin, be sure to turn off your laptop and unplug it from the outlet.
Use a Phillips screwdriver to remove the ten 7.5mm screws that securing the back panel.
Use the plastic opening tool to pry up and loosen the back panel.
Remove the back panel.
1024
Step 2
- Use a Phillips screwdriver to remove the two 3 mm screws securing the battery.
- Unclip the hard drive wire from the battery.
Use a Phillips screwdriver to remove the two 3 mm screws securing the battery.
Unclip the hard drive wire from the battery.
Step 3
- Gently remove the battery from the rest of the device.
Gently remove the battery from the rest of the device.
Step 4
Hinge
- Remove the three 8mm screws with the Phillips #0 head connected to each of the hinges.
- Take out the antenna cables from the routing guide on the hinge cover by pulling them from their original position
Remove the three 8mm screws with the Phillips #0 head connected to each of the hinges.
Take out the antenna cables from the routing guide on the hinge cover by pulling them from their original position
Step 5
- Lay the screen flat on a smooth flat surface to release the hinges.
Lay the screen flat on a smooth flat surface to release the hinges.
Step 6
- Use the plastic opening tool around the edges of the screen to separate the screen back from the display until the backing is loose enough to pull apart with your hands.
- The second image should be the result of removing the back of the screen.
Use the plastic opening tool around the edges of the screen to separate the screen back from the display until the backing is loose enough to pull apart with your hands.
The second image should be the result of removing the back of the screen.
Step 7
- Locate the hinge or hinges that need to be replaced and remove the two, or four, 3mm screws with the Phillips #0 head.
- Remove the single, (or both, depending on if you are replacing one or both hinges) 6mm screw(s) from the top of the hinge with the Phillips #0 head.
Locate the hinge or hinges that need to be replaced and remove the two, or four, 3mm screws with the Phillips #0 head.
Remove the single, (or both, depending on if you are replacing one or both hinges) 6mm screw(s) from the top of the hinge with the Phillips #0 head.
Step 8
- Grasp the hinge from the edge as shown and separate the hinge from the display.
Grasp the hinge from the edge as shown and separate the hinge from the display.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Mikinna Martin
Member since: 09/25/2015
458 Reputation
2 Guides authored
Badges:
13
+10 more badges
Team
University of Tampa, Team 1-5, Whiteside Fall 2015
Member of University of Tampa, Team 1-5, Whiteside Fall 2015
UT-WHITESIDE-F15S1G5
3 Members
6 Guides authored
