Difficulty

Moderate

Steps

13

Time Required

                          15 minutes            

Sections

3

  • Back Panel
  • 3 steps
  • Battery
  • 4 steps
  • Solid State Drive
  • 6 steps

Flags

0

  • BackDell Inspiron 11-3152

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Panel               
  • Flip the computer over.

Flip the computer over.

1024

Step 2

  • Remove all nine 5mm Phillips head screws from the back cover using #0 Phillips head.

Remove all nine 5mm Phillips head screws from the back cover using #0 Phillips head.

Step 3

  • Gently use a spudger to pull the cover away from the rest of the laptop. The cover will come off after you use the tool on two or three sides.

Gently use a spudger to pull the cover away from the rest of the laptop. The cover will come off after you use the tool on two or three sides.

Step 4

              Battery               
  • Make sure that the power is off.
  • After taking off the back panel, you will see the battery located at the bottom of the computer system. It’s black and is clearly labeled “dell battery”.

Make sure that the power is off.

After taking off the back panel, you will see the battery located at the bottom of the computer system. It’s black and is clearly labeled “dell battery”.

Step 5

  • Locate the battery at the bottom of the computer and remove the four 3mm screws with a Phillips #0 head that hold the battery down.

Locate the battery at the bottom of the computer and remove the four 3mm screws with a Phillips #0 head that hold the battery down.

Step 6

  • Remove the Solid State Drive wire from the battery clip by detaching the wire.
  • This can be done by gently pulling the connector away from the battery clip.

Remove the Solid State Drive wire from the battery clip by detaching the wire.

This can be done by gently pulling the connector away from the battery clip.

Step 7

  • Remove the battery from the computer system by gently lifting it from the side.

Remove the battery from the computer system by gently lifting it from the side.

Step 8

              Solid State Drive               
  • The Hard Disk Drive is the silver box at the left middle portion on top of the battery.

The Hard Disk Drive is the silver box at the left middle portion on top of the battery.

Step 9

  • Remove the no - fuss ribbon connector which connects the Solid State Drive to the motherboard.
  • Pull the two white clips with your fingers to release the connector pins.
  • After the pins have been opened, detach the ribbon connector by gently pulling it out from the port.

Remove the no - fuss ribbon connector which connects the Solid State Drive to the motherboard.

Pull the two white clips with your fingers to release the connector pins.

After the pins have been opened, detach the ribbon connector by gently pulling it out from the port.

Step 10

  • Remove all three 2mm screws holding down the Solid State Drive by using a #0 Phillips head.

Remove all three 2mm screws holding down the Solid State Drive by using a #0 Phillips head.

Step 11

  • Remove the two ZIF connectors , which connect Hard Disk Drive to the motherboard.
  • Pull apart the black tape on top of the ZIF connector with fingers
  • Pull the tape upwards with your fingers to remove the ZIF connector.
  • If you are having trouble, use the spudger to pry it up.

Remove the two ZIF connectors , which connect Hard Disk Drive to the motherboard.

Pull apart the black tape on top of the ZIF connector with fingers

Pull the tape upwards with your fingers to remove the ZIF connector.

If you are having trouble, use the spudger to pry it up.

Step 12

  • Remove the tape attached to the Solid State Drive by simply pulling them off with fingers.

Remove the tape attached to the Solid State Drive by simply pulling them off with fingers.

Step 13

  • Remove the Solid State Drive by simply lifting it away from the laptop.

Remove the Solid State Drive by simply lifting it away from the laptop.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 

                    derek odoi                     

Member since: 03/08/2016

137 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges                           

Team

                       UMass Dartmouth, Team 4-6, Catania Spring 2016                        

                                                  Member of UMass Dartmouth, Team 4-6, Catania Spring 2016 



                    UMASSD-CATANIA-S16S4G6                     


                                            3 Members                     


                                            6 Guides authored