Difficulty
Moderate
Steps
13
Time Required
10 - 15 minutes
Sections
3
- Back Cover
- 2 steps
- Battery
- 3 steps
- Display
- 8 steps
Flags
0
BackDell Chromebook 3100 2-in-1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Note: Some Dell Chromebook 3100 configurations don’t have a touch screen.
What you need
Step 1
Back Cover
- Using a Phillips #1 screwdriver, remove all nine of the 5 mm screws from the back cover.
Using a Phillips #1 screwdriver, remove all nine of the 5 mm screws from the back cover.
1024
Step 2
- Use the opening tool to pry the back cover off of the device.
Use the opening tool to pry the back cover off of the device.
Step 3
Battery
- Disconnect the battery cable from the connector on the system board.
Disconnect the battery cable from the connector on the system board.
Step 4
- Using a Phillips #1 screwdriver, remove the three 4 mm screws that secure the battery.
- Remove the adhesive tape that secures the battery in place.
Using a Phillips #1 screwdriver, remove the three 4 mm screws that secure the battery.
Remove the adhesive tape that secures the battery in place.
Step 5
- Carefully remove the battery from the device.
Carefully remove the battery from the device.
Step 6
Display
- Remove the single 3 mm screw that secures the WLAN bracket to the system board using a Phillips #1 screwdriver.
- Lift the WLAN bracket from the system board.
- After lifting the bracket, carefully unplug the two coaxial cables.
Remove the single 3 mm screw that secures the WLAN bracket to the system board using a Phillips #1 screwdriver.
Lift the WLAN bracket from the system board.
After lifting the bracket, carefully unplug the two coaxial cables.
Step 7
- Remove the single 4 mm screw that secures the eDP bracket to the motherboard using a Phillips #1 screwdriver.
- Remove the eDP bracket.
Remove the single 4 mm screw that secures the eDP bracket to the motherboard using a Phillips #1 screwdriver.
Remove the eDP bracket.
Step 8
- Disconnect the display cable from the motherboard by using a plastic opening pick.
Disconnect the display cable from the motherboard by using a plastic opening pick.
Step 9
- Open the system to 180 degrees and place the computer on a flat surface, with the display hinges facing up.
Open the system to 180 degrees and place the computer on a flat surface, with the display hinges facing up.
Step 10
- Remove the three (on both hinges) 5 mm display hinge bracket screws that secure the display assembly to the system using a Phillips #1 screwdriver.
Remove the three (on both hinges) 5 mm display hinge bracket screws that secure the display assembly to the system using a Phillips #1 screwdriver.
Step 11
- Remove the display assembly from the system.
Remove the display assembly from the system.
Step 12
- Use the opening tool to open the display panel starting from the pry points located above the left and right hinges.
- Work your way around, through the left and right side of the panel, and carefully flip the display panel over.
Use the opening tool to open the display panel starting from the pry points located above the left and right hinges.
Work your way around, through the left and right side of the panel, and carefully flip the display panel over.
Step 13
- Peel back the adhesive tape securing the display cable on the back of the display panel and separate the display.
Peel back the adhesive tape securing the display cable on the back of the display panel and separate the display.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
M Ali
Member since: 11/03/2021
253 Reputation
2 Guides authored
Badges:
5
+2 more badges
Team
Gateway, Team 1-1, Pee Fall 2021
Member of Gateway, Team 1-1, Pee Fall 2021
GCC-PEE-F21S1G1
5 Members
5 Guides authored
