Difficulty

Easy

Steps

7

Time Required

                          2 - 5 minutes

Sections

1

  • LCD screen
  • 7 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackDell Chromebook 11-3120/P22T

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Open the Chromebook (Flat)
  • Open the chromebook until it is completely flat. The LCD top cover should touch the desk.

Open the chromebook until it is completely flat. The LCD top cover should touch the desk.

1024

Step 2

              Remove bezel frame screws and covers
  • Remove the both the top left and right corner screw covers using the metal spudger tool within your iFixit Toolkit.
  • There may be a thin layer of adhesive left behind the screw cover. You can peel this away with this same metal spudger tool.
  • Remove the 2 screws with a Phillips #0 or #00 screwdriver.

Remove the both the top left and right corner screw covers using the metal spudger tool within your iFixit Toolkit.

There may be a thin layer of adhesive left behind the screw cover. You can peel this away with this same metal spudger tool.

Remove the 2 screws with a Phillips #0 or #00 screwdriver.

Step 3

              Remove bezel frame
  • Using the metal spudger or your favorite pry tool, lightly seperate the bezel frame from the chromebook. Start in one of the top corners near the screws.

Using the metal spudger or your favorite pry tool, lightly seperate the bezel frame from the chromebook. Start in one of the top corners near the screws.

Step 4

              Remove LCD screws
  • Remove the 4 LCD screws in each corner of the screen. Make sure to just unscrew the 4 corner screws as the other screws are not needed.

Remove the 4 LCD screws in each corner of the screen. Make sure to just unscrew the 4 corner screws as the other screws are not needed.

Step 5

              Remove LCD and disconnect LCD Connector
  • Lift the LCD out from within the frame and carefull flip the LCD over slowly torward you and set it ontop of the keyboard.
  • Then disconnect the LCD connector which is located behind the LCD

Lift the LCD out from within the frame and carefull flip the LCD over slowly torward you and set it ontop of the keyboard.

Then disconnect the LCD connector which is located behind the LCD

Step 6

              Install new LCD & replace screws
  • Start by holding the new LCD with the backside (white) facing up so you will have access to the LCD cable connector.
  • Then connect the LCD cable to the new LCD connector located on the back of the new LCD screen.
  • Replace the 4 LCD screws in each corner of the screen.

Start by holding the new LCD with the backside (white) facing up so you will have access to the LCD cable connector.

Then connect the LCD cable to the new LCD connector located on the back of the new LCD screen.

Replace the 4 LCD screws in each corner of the screen.

Step 7

              Install LCD bezel frame & Replace screws
  • Start by holding the LCD bezel frame over the 2 LCD hinges. Then snap the bezel frame together along all sides. You should hear “snapping” sounds so do not worry :)
  • Replace the 2 LCD bezel frame screws. You do not necessarily to replace the screw covers as they do not stay on very well anyways.

Start by holding the LCD bezel frame over the 2 LCD hinges. Then snap the bezel frame together along all sides. You should hear “snapping” sounds so do not worry :)

Replace the 2 LCD bezel frame screws. You do not necessarily to replace the screw covers as they do not stay on very well anyways.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      11 other people completed this guide.

Author

                                      with 2 other contributors 


                    Jon

Member since: 08/18/2013

3,901 Reputation

                                      22 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Phing Chov - Apr 26, 2017

Reply

Thanks for this guide! It saved me a lot of time. I was removing the entire LCD assembly from the base to pull apart the frame. I didn’t realize you can keep the assembly attached and still remove the LCD.

Jon - Jun 5, 2017

Reply

Awesome, you’re welcome! I am glad it could help. Thanks for the kind words.

DeeAnne Mason - Nov 17, 2017

Reply

great easy to follow instructions! Thanks.

Jon - Dec 4, 2017

Anthony Gross - Feb 25, 2021

Reply

Thank you for taking your time and writing this. .