Difficulty

Easy

Steps

13

Time Required

                          10 - 20 minutes            

Sections

1

  • Hard Drive
  • 13 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackDell Alienware 18 (R1)

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Disconnecting the Hard-Drive Cable               
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before You Begin.
  • CAUTION: To avoid data loss, do not remove the hard drive while the computer is in Sleep or On state.
  • CAUTION: Hard drives are extremely fragile. Exercise care when handling the hard drive.
  • Disconnect the hard-drive cable from its connector on the system board.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before You Begin.

CAUTION: To avoid data loss, do not remove the hard drive while the computer is in Sleep or On state.

CAUTION: Hard drives are extremely fragile. Exercise care when handling the hard drive.

Disconnect the hard-drive cable from its connector on the system board.

1024

Step 2

              Loosen the Screws               
  • Loosen the captive screws that secure the hard-drive assembly to the computer base.

Loosen the captive screws that secure the hard-drive assembly to the computer base.

Step 3

              Lifting the Hard-Drive Assembly               
  • Using the pull-tab, lift the hard-drive assembly out of the computer base.

Using the pull-tab, lift the hard-drive assembly out of the computer base.

Step 4

              Disconnecting the Interposer               
  • Disconnect the interposer from the hard drives.
  • NOTE: Your computer supports up to three drives.

Disconnect the interposer from the hard drives.

NOTE: Your computer supports up to three drives.

Step 5

              Remove the Screws               
  • Remove the screws that secure the hard drive(s) to the hard-drive bracket and slide the hard drive(s) out of the hard-drive bracket.

Remove the screws that secure the hard drive(s) to the hard-drive bracket and slide the hard drive(s) out of the hard-drive bracket.

Step 6

              Placing the Hard-Drive               
  • Place the NEW primary hard drive in the hard-drive bracket.

Place the NEW primary hard drive in the hard-drive bracket.

Step 7

              Sliding the Secondary Hard-Drive               
  • If applicable, slide the secondary hard drive into the hard-drive bracket.

If applicable, slide the secondary hard drive into the hard-drive bracket.

Step 8

              Secure the Screws               
  • Replace the screws that secure the primary hard drive to the hard-drive bracket.

Replace the screws that secure the primary hard drive to the hard-drive bracket.

Step 9

              Replace the Screws               
  • If applicable, replace the screws that secure the secondary hard drive to the hard-drive bracket.

If applicable, replace the screws that secure the secondary hard drive to the hard-drive bracket.

Step 10

              Connecting the Interposer               
  • Connect the interposer to the hard drives.

Connect the interposer to the hard drives.

Step 11

              Placing the Hard-Drive Assembly               
  • Place the hard-drive assembly in the computer base.

Place the hard-drive assembly in the computer base.

Step 12

              Tightening the Screws               
  • Tighten the captive screws that secure the hard-drive assembly to the computer base.

Tighten the captive screws that secure the hard-drive assembly to the computer base.

Step 13

              Connecting the Hard-Drive               
  • Connect the hard-drive cable to its connector on the system board.

Connect the hard-drive cable to its connector on the system board.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 5 other contributors 

                    darrius                     

Member since: 03/26/2018

5,213 Reputation

                                      30 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored