Difficulty
Moderate
Steps
7
Time Required
25 - 45 minutes
Sections
3
- Back Case
- 2 steps
- Inside Chassey
- 3 steps
- Battery
- 2 steps
Flags
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Needs More Images
A few more images would make this guide’s procedures crystal clear.
Better Introduction
Improve this guide by completing or revising its introduction.
BackDell Alienware 15 R3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Case
- Before you begin, turn off the laptop and unplug the charger.
- Flip the laptop over so that the backside is facing up.
- Use a Phillips #00 screwdriver to remove the six 13.0 mm screws from the sides of the back case.
- Use a Phillips #00 screwdriver to remove one 5.0 mm screw from the back of the laptop.
Before you begin, turn off the laptop and unplug the charger.
Flip the laptop over so that the backside is facing up.
Use a Phillips #00 screwdriver to remove the six 13.0 mm screws from the sides of the back case.
Use a Phillips #00 screwdriver to remove one 5.0 mm screw from the back of the laptop.
1024
Step 2
- Use the opening tool to pry the back case from the computer.
- Use the opening tool and work your way around the perimeter of the back case to gently release the clips.
- Start from the black vent for an easier removal.
- Lift the back case off of the laptop.
Use the opening tool to pry the back case from the computer.
Use the opening tool and work your way around the perimeter of the back case to gently release the clips.
Start from the black vent for an easier removal.
Lift the back case off of the laptop.
Step 3
Inside Chassey
- Use a Phillips #00 screwdriver to remove two screws from the side of the laptop.
Use a Phillips #00 screwdriver to remove two screws from the side of the laptop.
Step 4
- Use an opening tool to release the four tabs from the hinge cover and gently pry it off.
Use an opening tool to release the four tabs from the hinge cover and gently pry it off.
Step 5
- Use a Phillips #00 screwdriver to remove nine screws from the chassis.
- Use a spudger or opening tool to remove the chassis and reveal the battery, fan, motherboard, and other components.
Use a Phillips #00 screwdriver to remove nine screws from the chassis.
Use a spudger or opening tool to remove the chassis and reveal the battery, fan, motherboard, and other components.
Step 6
Battery
- Use a Phillips #00 screwdriver to remove the 5.0 mm screw that is securing the battery to the palm rest assembly.
Use a Phillips #00 screwdriver to remove the 5.0 mm screw that is securing the battery to the palm rest assembly.
Step 7
- To the upper right of the battery is a connecting cable. Gently disconnect it from the palm rest assembly.
- Confirm nothing else is connected to the battery and lift the battery completely off the palm rest assembly.
To the upper right of the battery is a connecting cable. Gently disconnect it from the palm rest assembly.
Confirm nothing else is connected to the battery and lift the battery completely off the palm rest assembly.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Jake Nelson
Member since: 09/22/2022
578 Reputation
7 Guides authored
Badges:
4
+1 more badge
Team
University of North Texas, Team 4-1, Saru Jimmy Fall 2022
Member of University of North Texas, Team 4-1, Saru Jimmy Fall 2022
UNT-SARU JIMMY-F22S4G1
4 Members
7 Guides authored
