Difficulty

Easy

Steps

20

Time Required

                          3 - 6 minutes

Sections

3

  • Base Cover
  • 6 steps
  • Battery
  • 10 steps
  • Memory Module
  • 4 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackDell Alienware 14

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Close the Display
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before You Begin. . After working inside your computer, follow the instructions in “After Working Inside Your Computer”.
  • Close the display, and turn the computer over.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before You Begin. . After working inside your computer, follow the instructions in “After Working Inside Your Computer”.

Close the display, and turn the computer over.

1024

Step 2

              Remove the Screws
  • Remove the screws that secure the base cover to the computer base.

Remove the screws that secure the base cover to the computer base.

Step 3

              Slide and Lift the Base Cover
  • Slide and lift the base cover off the computer base.

Slide and lift the base cover off the computer base.

Step 4

              Align the Tabs
  • Align the tabs on the NEW base cover with the slots on the computer base and slide the base cover into place.

Align the tabs on the NEW base cover with the slots on the computer base and slide the base cover into place.

Step 5

              Replace the Screws
  • Replace the screws that secure the base cover to the computer base.

Replace the screws that secure the base cover to the computer base.

Step 6

              Turn the Computer Over
  • Turn the computer over and open the display.

Turn the computer over and open the display.

Step 7

              Disconnecting the Battery Cable
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Disconnect the battery cable from the system-board connector.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Disconnect the battery cable from the system-board connector.

Step 8

              Remove the Screws
  • Remove the screws that secure the battery to the computer base.

Remove the screws that secure the battery to the computer base.

Step 9

              Using the Battery Cable
  • Using the battery cable, lift the battery and release it from the tabs on the computer base.

Using the battery cable, lift the battery and release it from the tabs on the computer base.

Step 10

              Turn the Computer Over
  • Turn the computer over and open the display as far as possible.

Turn the computer over and open the display as far as possible.

Step 11

              The Power Button
  • Press and hold the power button for five seconds to ground the system board.

Press and hold the power button for five seconds to ground the system board.

Step 12

              Close the Display
  • Close the display and turn the computer over.

Close the display and turn the computer over.

Step 13

              Align the Tabs
  • Align the tabs on the NEW battery with the slots on the computer base.

Align the tabs on the NEW battery with the slots on the computer base.

Step 14

              Align the Screw Holes
  • Align the screw holes on the battery with the screw holes on the computer base.

Align the screw holes on the battery with the screw holes on the computer base.

Step 15

              Replace the Screws
  • Replace the screws that secure the battery to the computer base.

Replace the screws that secure the battery to the computer base.

Step 16

              Connect the Battery Cable
  • Connect the battery cable to the system-board connector.

Connect the battery cable to the system-board connector.

Step 17

              Popping up the Memory Module
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • CAUTION: To prevent damage to the memory-module connector, do not use tools to spread the memory-module securing clips.
  • Using your fingertips, carefully spread apart the securing clips on each end of the memory-module connector until the memory module pops up.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

CAUTION: To prevent damage to the memory-module connector, do not use tools to spread the memory-module securing clips.

Using your fingertips, carefully spread apart the securing clips on each end of the memory-module connector until the memory module pops up.

Step 18

              Remove the Memory Module
  • Remove the memory module from the memory-module connector.

Remove the memory module from the memory-module connector.

Step 19

              Align the Notch
  • Align the notch on the NEW memory module with the tab on the memory-module connector.

Align the notch on the NEW memory module with the tab on the memory-module connector.

Step 20

              Slide the Memory Module
  • Slide the memory module firmly into the slot at a 45-degree angle, and press the memory module down until it clicks into place. If you do not hear the click, remove the memory module and reinstall it.
  • NOTE: If the memory module is not installed properly, the computer may not boot.

Slide the memory module firmly into the slot at a 45-degree angle, and press the memory module down until it clicks into place. If you do not hear the click, remove the memory module and reinstall it.

NOTE: If the memory module is not installed properly, the computer may not boot.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Terrence15

Member since: 12/18/2017

78,526 Reputation

                                      441 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored