Difficulty

Moderate

Steps

82

Time Required

Suggest a time??

Sections

8

  • Base Cover
  • 6 steps
  • Battery
  • 10 steps
  • Secondary Hard Drive
  • 18 steps
  • Palm Rest
  • 14 steps
  • Display Assembly
  • 18 steps
  • Display Bezel
  • 3 steps
  • Display Hinges
  • 4 steps
  • Display Panel
  • 9 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackDell Alienware 14

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Close the Display
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before You Begin. . After working inside your computer, follow the instructions in “After Working Inside Your Computer”.
  • Close the display, and turn the computer over.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before You Begin. . After working inside your computer, follow the instructions in “After Working Inside Your Computer”.

Close the display, and turn the computer over.

1024

Step 2

              Remove the Screws
  • Remove the screws that secure the base cover to the computer base.

Remove the screws that secure the base cover to the computer base.

Step 3

              Slide and Lift the Base Cover
  • Slide and lift the base cover off the computer base.

Slide and lift the base cover off the computer base.

Step 4

              Align the Tabs
  • Align the tabs on the NEW base cover with the slots on the computer base and slide the base cover into place.

Align the tabs on the NEW base cover with the slots on the computer base and slide the base cover into place.

Step 5

              Replace the Screws
  • Replace the screws that secure the base cover to the computer base.

Replace the screws that secure the base cover to the computer base.

Step 6

              Turn the Computer Over
  • Turn the computer over and open the display.

Turn the computer over and open the display.

Step 7

              Disconnecting the Battery Cable
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Disconnect the battery cable from the system-board connector.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Disconnect the battery cable from the system-board connector.

Step 8

              Remove the Screws
  • Remove the screws that secure the battery to the computer base.

Remove the screws that secure the battery to the computer base.

Step 9

              Using the Battery Cable
  • Using the battery cable, lift the battery and release it from the tabs on the computer base.

Using the battery cable, lift the battery and release it from the tabs on the computer base.

Step 10

              Turn the Computer Over
  • Turn the computer over and open the display as far as possible.

Turn the computer over and open the display as far as possible.

Step 11

              The Power Button
  • Press and hold the power button for five seconds to ground the system board.

Press and hold the power button for five seconds to ground the system board.

Step 12

              Close the Display
  • Close the display and turn the computer over.

Close the display and turn the computer over.

Step 13

              Align the Tabs
  • Align the tabs on the NEW battery with the slots on the computer base.

Align the tabs on the NEW battery with the slots on the computer base.

Step 14

              Align the Screw Holes
  • Align the screw holes on the battery with the screw holes on the computer base.

Align the screw holes on the battery with the screw holes on the computer base.

Step 15

              Replace the Screws
  • Replace the screws that secure the battery to the computer base.

Replace the screws that secure the battery to the computer base.

Step 16

              Connect the Battery Cable
  • Connect the battery cable to the system-board connector.

Connect the battery cable to the system-board connector.

Step 17

              Remove the Screws
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • CAUTION: To avoid data loss, do not remove the hard drive while the computer is On or in Sleep state.
  • CAUTION: Hard drives are extremely fragile. Exercise care when handling the hard drive.
  • NOTE: The secondary hard-drive or solid-state drive is optional and can be installed in the optical drive bay.
  • Remove the screws that secure the secondary hard-drive assembly to the computer base.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

CAUTION: To avoid data loss, do not remove the hard drive while the computer is On or in Sleep state.

CAUTION: Hard drives are extremely fragile. Exercise care when handling the hard drive.

NOTE: The secondary hard-drive or solid-state drive is optional and can be installed in the optical drive bay.

Remove the screws that secure the secondary hard-drive assembly to the computer base.

Step 18

              Lifting the Secondary Hard-Drive
  • Carefully lift the secondary hard-drive assembly and then lift the latches to release the secondary hard-drive cable from the system-board connector.

Carefully lift the secondary hard-drive assembly and then lift the latches to release the secondary hard-drive cable from the system-board connector.

Step 19

              Lifting the Hard Drive
  • Lift the secondary hard-drive assembly off the computer base.

Lift the secondary hard-drive assembly off the computer base.

Step 20

              Turn the Assembly Over
  • Turn the secondary hard-drive assembly over.

Turn the secondary hard-drive assembly over.

Step 21

              Remove the Screw
  • Remove the screw that secures the secondary hard-drive assembly to the main bracket.

Remove the screw that secures the secondary hard-drive assembly to the main bracket.

Step 22

              Remove the Screws
  • Remove the screws that secure the secondary hard-drive to the secondary hard-drive bracket.

Remove the screws that secure the secondary hard-drive to the secondary hard-drive bracket.

Step 23

              Slide and Lift the Hard-Drive
  • Slide and lift the secondary hard-drive off the secondary hard-drive bracket.

Slide and lift the secondary hard-drive off the secondary hard-drive bracket.

Step 24

              Disconnect the Interposer
  • Disconnect the interposer from the secondary hard-drive connector.

Disconnect the interposer from the secondary hard-drive connector.

Step 25

              Connect the Interposer
  • Connect the interposer to the secondary hard-drive connector.

Connect the interposer to the secondary hard-drive connector.

Step 26

              Placing the Secondary Hard-Drive
  • Place the NEW secondary hard-drive in the secondary hard-drive bracket.

Place the NEW secondary hard-drive in the secondary hard-drive bracket.

Step 27

              Align the Screw Holes
  • Align the screw holes on the secondary hard-drive with the screw holes on the secondary hard-drive bracket.

Align the screw holes on the secondary hard-drive with the screw holes on the secondary hard-drive bracket.

Step 28

              Replace the Screws
  • Replace the screws that secure the secondary hard-drive to the secondary hard-drive bracket.

Replace the screws that secure the secondary hard-drive to the secondary hard-drive bracket.

Step 29

              Align the Screw Hole
  • Align the screw hole on the secondary hard-drive assembly with the screw hole on the main bracket.

Align the screw hole on the secondary hard-drive assembly with the screw hole on the main bracket.

Step 30

              Replace the Screw
  • Replace the screw that secures the secondary hard-drive assembly to the main bracket.

Replace the screw that secures the secondary hard-drive assembly to the main bracket.

Step 31

              Turn the Hard-Drive Assembly Over

Step 32

              Slide the Hard-Drive Cable
  • Slide the secondary hard-drive cable into the system-board connector and press down on the connector latches to secure the cable.

Slide the secondary hard-drive cable into the system-board connector and press down on the connector latches to secure the cable.

Step 33

              Align the Screw Holes
  • Align the screw holes on the secondary hard-drive assembly with the screw holes on the computer base.

Align the screw holes on the secondary hard-drive assembly with the screw holes on the computer base.

Step 34

              Replace the Screws
  • Replace the screws that secure the secondary hard-drive assembly to the computer base.

Replace the screws that secure the secondary hard-drive assembly to the computer base.

Step 35

              Disconnecting the Status-Light Board Cable
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Lift the connector latch and pull the pull-tab to disconnect the status-light board cable from the system-board connector and slide the cable into the slot on the computer base.

Lift the connector latch and pull the pull-tab to disconnect the status-light board cable from the system-board connector and slide the cable into the slot on the computer base.

Step 36

              Remove the Screws
  • Remove the screws that secure the palm -rest assembly to the computer base.

Remove the screws that secure the palm -rest assembly to the computer base.

Step 37

              Turn the Computer Over
  • Turn the computer over and open the display as far as possible.

Turn the computer over and open the display as far as possible.

Step 38

              Pry the Palm-Rest Assembly
  • Using a plastic scribe, pry the palm-rest assembly from the computer base.

Using a plastic scribe, pry the palm-rest assembly from the computer base.

Step 39

              Lift the Palm-Rest Assembly
  • Carefully lift the palm-rest assembly and turn it over.

Carefully lift the palm-rest assembly and turn it over.

Step 40

              Release the Connector Latches
  • Release the connector latches to disconnect the flexi-cable from the system board.

Release the connector latches to disconnect the flexi-cable from the system board.

Step 41

              Follow the Instructions
  • Follow the instructions from step 1 to step 9 in Removing the Keyboard.
  • Follow the instructions from step 1 to step 4 in Removing the Status-Light Board.
  • Follow the instructions from step 1 to step 4 in Removing the Speakers.
  • Follow the instructions from step 1 to step 4 in Removing the Power-Button Board.

Follow the instructions from step 1 to step 9 in Removing the Keyboard.

Follow the instructions from step 1 to step 4 in Removing the Status-Light Board.

Follow the instructions from step 1 to step 4 in Removing the Speakers.

Follow the instructions from step 1 to step 4 in Removing the Power-Button Board.

Step 42

              Follow Instructions
  • Follow the instructions from step 1 to step 4 in Replacing the Power-Button Board.
  • Follow the instructions from step 1 to step 3 in Replacing the Speakers.
  • Follow the instructions from step 1 to step 4 in Removing the Status-Light Board.
  • Follow the instructions from step 1 to step 8 in Replacing the Keyboard.

Follow the instructions from step 1 to step 4 in Replacing the Power-Button Board.

Follow the instructions from step 1 to step 3 in Replacing the Speakers.

Follow the instructions from step 1 to step 8 in Replacing the Keyboard.

Step 43

              Connect the Flexi-Cable
  • Connect the flexi-cable to the connector on the system board.

Connect the flexi-cable to the connector on the system board.

Step 44

              Turn the Palm-Rest Assembly
  • Turn the NEW palm-rest assembly over and slide the status-light board cable through the slot on the computer base.

Turn the NEW palm-rest assembly over and slide the status-light board cable through the slot on the computer base.

Step 45

              Align the Palm-Rest Assembly
  • Align the palm-rest assembly over the computer base and snap the palm-rest assembly into place.

Align the palm-rest assembly over the computer base and snap the palm-rest assembly into place.

Step 46

              Close the Display

Step 47

              Replace the Screws
  • Replace the screws that secure the palm-rest assembly to the computer base.

Replace the screws that secure the palm-rest assembly to the computer base.

Step 48

              Slide the Status-Light Board Cable
  • Slide the status-light board cable into the system-board connector and press on the connector latch to secure the cable.

Slide the status-light board cable into the system-board connector and press on the connector latch to secure the cable.

Step 49

              Close the Display
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Close the display and turn the computer over.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Step 50

              Disconnecting the Display
  • Disconnect the display and camera cables from the system-board connectors.

Disconnect the display and camera cables from the system-board connectors.

Step 51

              Disconnect the Antenna Cables
  • Disconnect the antenna cables from the wireless mini-card.

Disconnect the antenna cables from the wireless mini-card.

Step 52

              Remove the Screws
  • Remove the screws that secure the display assembly to the computer base.

Remove the screws that secure the display assembly to the computer base.

Step 53

              Turn the Computer Over

Step 54

              Remove the Cables
  • Remove the display, camera, and antenna cables from the slots on the computer base.

Remove the display, camera, and antenna cables from the slots on the computer base.

Step 55

              Note the Cable-Routing
  • Note the display, camera and antenna cable-routing and remove the cables from their routing guides.

Note the display, camera and antenna cable-routing and remove the cables from their routing guides.

Step 56

              Slide the Cables
  • Slide the cables through the slots on the computer base.

Slide the cables through the slots on the computer base.

Step 57

              Remove the Screws

Step 58

              Lifting the Display Assembly
  • Lift the display assembly off the computer base.

Lift the display assembly off the computer base.

Step 59

              Align the Screw Holes
  • Align the screw holes on the NEW display assembly with the screw holes on the computer base.

Align the screw holes on the NEW display assembly with the screw holes on the computer base.

Step 60

              Replace the Screws
  • Replace the screws that secure the display assembly to the computer base.

Replace the screws that secure the display assembly to the computer base.

Step 61

              Slide the Cables

Step 62

              Close the Display

Step 63

              Route the Cables
  • Route the display, camera, and antenna cables through the routing guides.

Route the display, camera, and antenna cables through the routing guides.

Step 64

              Replace the Screws

Step 65

              Connecting the Cables
  • Connect the display and camera cables to the system-board connectors.

Connect the display and camera cables to the system-board connectors.

Step 66

              Connecting the Antenna Cables
  • Connect the antenna cables to the wireless mini-card.

Connect the antenna cables to the wireless mini-card.

Step 67

              Prying the Edge of the Display Bezel
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Using your fingertips, carefully pry up the inside edge of the display bezel

Using your fingertips, carefully pry up the inside edge of the display bezel

Step 68

              Remove the Display Bezel
  • Remove the display bezel off the display back-cover.

Remove the display bezel off the display back-cover.

Step 69

              Aligning the Display Bezel
  • Align the NEW display bezel with the display back-cover, and gently snap the display bezel into place.

Align the NEW display bezel with the display back-cover, and gently snap the display bezel into place.

Step 70

              Remove the Screws
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Remove the screws that secure the display hinges to the display back-cover.

Remove the screws that secure the display hinges to the display back-cover.

Step 71

              Remove the Display Hinges
  • Remove the display hinges off the display back-cover.

Remove the display hinges off the display back-cover.

Step 72

              Align the Screw Holes
  • Align the screw holes on the NEW display hinges with the screw holes on the display back-cover.

Align the screw holes on the NEW display hinges with the screw holes on the display back-cover.

Step 73

              Replace the Screws
  • Replace the screws that secure the display hinges to the display back-cover.

Replace the screws that secure the display hinges to the display back-cover.

Step 74

              Remove the Screws
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Remove the screws that secure the display panel to the display back-cover.

Remove the screws that secure the display panel to the display back-cover.

Step 75

              Placing the Display Back-Cover
  • Carefully turn the display panel over and place it on the display back-cover.

Carefully turn the display panel over and place it on the display back-cover.

Step 76

              Peeling the Tape
  • Peel the tape that secures the display cable to the display-panel connector.

Peel the tape that secures the display cable to the display-panel connector.

Step 77

              Lifting the Connector Latch
  • Lift the connector latch and disconnect the display cable from the display-panel connector.

Lift the connector latch and disconnect the display cable from the display-panel connector.

Step 78

              Lifting the Display Panel
  • Lift the display panel off the display back-cover.

Lift the display panel off the display back-cover.

Step 79

              Connecting the Display Cable
  • Connect the display cable to the display-panel connector and press down on the connector latch to secure the cable.

Connect the display cable to the display-panel connector and press down on the connector latch to secure the cable.

Step 80

              Adhering the Tape
  • Adhere the tape to secure the display cable.

Adhere the tape to secure the display cable.

Step 81

              Rotate the Display Panel
  • Carefully rotate the NEW display panel and align the screw holes on the display panel with the screw holes on the display back-cover.

Carefully rotate the NEW display panel and align the screw holes on the display panel with the screw holes on the display back-cover.

Step 82

              Replace the Screws
  • Replace the screws that secure the display panel to the display back-cover.

Replace the screws that secure the display panel to the display back-cover.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Terrence15

Member since: 12/18/2017

78,526 Reputation

                                      441 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored