Difficulty

Difficult

Steps

134

Time Required

Suggest a time??

Sections

15

  • Base Cover
  • 8 steps
  • Wireless Card
  • 8 steps
  • Solid-State Drive
  • 4 steps
  • Memory Modules
  • 4 steps
  • Rear-I/O Cover
  • 5 steps
  • Computer Base
  • 8 steps
  • Coin-Cell Battery
  • 4 steps
  • Heat-Sink Assembly
  • 8 steps
  • Battery
  • 4 steps
  • System Board
  • 27 steps
  • Display Assembly
  • 14 steps
  • Display Bezel
  • 11 steps
  • Camera
  • 6 steps
  • Display Panel
  • 10 steps
  • Display Hinges
  • 13 steps

Flags

2

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

Scenic Route

This guide’s procedure isn’t the most efficient way to get the job done, but still may be useful in some circumstances.

  • BackDell Alienware 13 R3

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Loosen the Screws
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Loosen the five captive screws that secure the base cover to the computer base.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Loosen the five captive screws that secure the base cover to the computer base.

1024

Step 2

              Pry the Base Cover
  • Using a plastic scribe, gently pry the base cover to release the tabs on the base cover from the slots on the computer base.

Using a plastic scribe, gently pry the base cover to release the tabs on the base cover from the slots on the computer base.

Step 3

              Lift the Base Cover
  • Lift the base cover off the computer base.

Lift the base cover off the computer base.

Step 4

              Disconnect the Battery Cable
  • Using a plastic scribe, disconnect the battery cable from the system board.

Using a plastic scribe, disconnect the battery cable from the system board.

Step 5

              Press and Hold the Power-Button
  • Press and hold the power button for five seconds to ground the system board.

Press and hold the power button for five seconds to ground the system board.

Step 6

              Connect the Battery Cable
  • Connect the battery cable to the system board.

Connect the battery cable to the system board.

Step 7

              Slide the Tabs
  • Slide the tabs on the NEW base cover into the slots on the computer base and snap the base cover into place

Slide the tabs on the NEW base cover into the slots on the computer base and snap the base cover into place

Step 8

              Tighten the Five Captive Screws
  • Tighten the five captive screws that secure the base cover to the computer base.

Tighten the five captive screws that secure the base cover to the computer base.

Step 9

              Align the Notch
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • CAUTION: To avoid damaging the wireless card, do not place any cables under it.
  • Remove the screw (M2x3) that secures the wireless card and bracket to the computer base.

CAUTION: To avoid damaging the wireless card, do not place any cables under it.

Remove the screw (M2x3) that secures the wireless card and bracket to the computer base.

Step 10

              Lift the Wireless-Card Bracket
  • Lift the wireless-card bracket off the wireless card.

Lift the wireless-card bracket off the wireless card.

Step 11

              Disconnecting the Antenna Cables
  • Disconnect the antenna cables from the wireless card.

Disconnect the antenna cables from the wireless card.

Step 12

              Align the Notch
  • CAUTION: To avoid damaging the wireless card, do not place any cables under it.
  • Align the notch on the wireless card with the tab on the wireless-card slot.

Align the notch on the wireless card with the tab on the wireless-card slot.

Step 13

              Slide the Wireless Card
  • Slide the NEW wireless card at an angle into the wireless-card slot.

Slide the NEW wireless card at an angle into the wireless-card slot.

Step 14

              Connect the Antenna Cables
  • Connect the antenna cables to the wireless card.

Connect the antenna cables to the wireless card.

Step 15

              Align the Screw Hole
  • Align the screw hole on the wireless-card bracket with the screw hole on the wireless card and the computer base.

Align the screw hole on the wireless-card bracket with the screw hole on the wireless card and the computer base.

Step 16

              Replace the Screw
  • Replace the screw (M2x3) that secures the wireless-card bracket to the wireless card and the computer base.

Replace the screw (M2x3) that secures the wireless-card bracket to the wireless card and the computer base.

Step 17

              Remove the Screw
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Remove the screw (M2x3) that secures the solid-state drive to the computer base.

Remove the screw (M2x3) that secures the solid-state drive to the computer base.

Step 18

              Lift and Slide the Solid-State Drive
  • Lift and slide the solid-state drive from the solid-state drive slot.

Lift and slide the solid-state drive from the solid-state drive slot.

Step 19

              Align the Notch
  • Align the notch on the NEW solid-state drive with the tab on the solid-state drive slot and slide the solid-state drive into the solid-state drive slot.

Align the notch on the NEW solid-state drive with the tab on the solid-state drive slot and slide the solid-state drive into the solid-state drive slot.

Step 20

              Press the Memory Module
  • Press the memory module down until it clicks into place.

Press the memory module down until it clicks into place.

Step 21

              Popping up the Memory Module
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Using your fingertips, carefully spread apart the securing clips on each end of the memory-module slot until the memory module pops up.

Using your fingertips, carefully spread apart the securing clips on each end of the memory-module slot until the memory module pops up.

Step 22

              Remove the Memory Module
  • Slide and remove the memory module from the memory-module slot.

Slide and remove the memory module from the memory-module slot.

Step 23

              Align the Notch
  • Align the notch on the NEW memory module with the tab on the memory-module slot and slide the memory module firmly into the slot at an angle.

Align the notch on the NEW memory module with the tab on the memory-module slot and slide the memory module firmly into the slot at an angle.

Step 24

              Press the Memory Module Down

Step 25

              Remove the Screws
  • Remove the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.

Remove the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.

Step 26

              Using a Plastic Scribe
  • Using a plastic scribe, gently release the tabs that secure rear-I/O cover to the computer base.

Using a plastic scribe, gently release the tabs that secure rear-I/O cover to the computer base.

Step 27

              Removing the Rear-I/O
  • Slide and remove the rear-I/O cover from the computer base.

Slide and remove the rear-I/O cover from the computer base.

Step 28

              Sliding the Rear-I/O
  • Slide the NEW rear-I/O cover into the slots on the computer base and snap the rear-I/O cover into place.

Slide the NEW rear-I/O cover into the slots on the computer base and snap the rear-I/O cover into place.

Step 29

              Replace the two Screws
  • Replace the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.

Replace the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.

Step 30

              Remove the Screws
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Remove the eleven (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Remove the eleven (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Step 31

              Remove the Screw
  • Remove the (M2x3) screw that secures the computer base to the palm-rest assembly.

Remove the (M2x3) screw that secures the computer base to the palm-rest assembly.

Step 32

              Remove the Two Screws
  • Remove the two (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Remove the two (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Step 33

              Lift the Computer Base
  • Lift the computer base from the palm-rest assembly.

Lift the computer base from the palm-rest assembly.

Step 34

              Align the Screw Holes
  • Align the screw holes on the NEW computer base with the screw holes on the palm-rest assembly.

Align the screw holes on the NEW computer base with the screw holes on the palm-rest assembly.

Step 35

              Replace the Screws
  • Replace the two (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Replace the two (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Step 36

              Replace the Screw
  • Replace the (M2x3) screw that secures the computer base to the palm-rest assembly.

Replace the (M2x3) screw that secures the computer base to the palm-rest assembly.

Step 37

              Replace the Eleven Screws
  • Replace the eleven (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Replace the eleven (M2.5x6L) screws that secure the computer base to the palm-rest assembly.

Step 38

              Disconnecting the Coin-Cell Battery
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that you note the BIOS setup program’s settings before removing the coin-cell battery.
  • Disconnect the coin-cell battery cable from the system board.

CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that you note the BIOS setup program’s settings before removing the coin-cell battery.

Disconnect the coin-cell battery cable from the system board.

Step 39

              Peeling the Coin-Cell Battery
  • Gently peel off the coin-cell battery along with its cable off the palm-rest assembly.

Gently peel off the coin-cell battery along with its cable off the palm-rest assembly.

Step 40

              Adhere the Coin-Cell Battery
  • Adhere the NEW coin-cell battery to the palm-rest assembly.

Adhere the NEW coin-cell battery to the palm-rest assembly.

Step 41

              Connect the Coin-Cell Battery
  • Connect the coin-cell battery cable to the system board.

Connect the coin-cell battery cable to the system board.

Step 42

              Disconnect the Left-Fan Cable
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • WARNING: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you touch it.
  • CAUTION: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your skin can reduce the heat transfer capability of the thermal grease.
  • Disconnect the left-fan cable from the system board.

WARNING: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you touch it.

CAUTION: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your skin can reduce the heat transfer capability of the thermal grease.

Disconnect the left-fan cable from the system board.

Step 43

              Disconnecting the Right-Fan Cable
  • Disconnect the right-fan cable from the system board.

Disconnect the right-fan cable from the system board.

Step 44

              Remove the Seven Screws
  • In sequential order (as indicated on the heat-sink assembly), remove the seven screws (M2x3) that secure the heat-sink assembly to the system board.

In sequential order (as indicated on the heat-sink assembly), remove the seven screws (M2x3) that secure the heat-sink assembly to the system board.

Step 45

              Lifiting the Heat-Sink Assembly
  • Lift the heat-sink assembly off the system board.

Lift the heat-sink assembly off the system board.

Step 46

              Align the Screw Holes
  • CAUTION: Incorrect alignment of the heat sink can damage the system board and processor.
  • NOTE: The original thermal grease can be reused if the original system board and fan are reinstalled together. If either the system board or the fan is replaced, use the thermal pad provided in the kit to ensure that thermal conductivity is achieved.
  • Align the screw holes on the NEW heat-sink assembly with the screw holes on the system board.

CAUTION: Incorrect alignment of the heat sink can damage the system board and processor.

NOTE: The original thermal grease can be reused if the original system board and fan are reinstalled together. If either the system board or the fan is replaced, use the thermal pad provided in the kit to ensure that thermal conductivity is achieved.

Align the screw holes on the NEW heat-sink assembly with the screw holes on the system board.

Step 47

              Replace the Screws
  • In sequential order (indicated on the heat-sink assembly), replace the seven screws (M2x3) that secure the heat-sink assembly to the system board.

In sequential order (indicated on the heat-sink assembly), replace the seven screws (M2x3) that secure the heat-sink assembly to the system board.

Step 48

              Connecting the Right-Fan Cable
  • Connect the right-fan cable to the respective connector on the system board.

Connect the right-fan cable to the respective connector on the system board.

Step 49

              Connecting the Left-Fan Cable
  • Connect the left-fan cable to the respective connector on the system board.

Connect the left-fan cable to the respective connector on the system board.

Step 50

              Peeling the Keyboard Connector
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Peel off the keyboard connector from the battery.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Peel off the keyboard connector from the battery.

Step 51

              Lifting the Battery
  • Lift the battery off the palm-rest assembly.

Lift the battery off the palm-rest assembly.

Step 52

              Placing the New Battery
  • CAUTION: Ensure the keyboard and keyboard-backlit cables are not under the battery.
  • Using the alignment post, place the NEW battery on the palm-rest assembly.

CAUTION: Ensure the keyboard and keyboard-backlit cables are not under the battery.

Using the alignment post, place the NEW battery on the palm-rest assembly.

Step 53

              Adhering the Keyboard
  • Adhere the keyboard connector that secures the battery to the palm-rest assembly.

Adhere the keyboard connector that secures the battery to the palm-rest assembly.

Step 54

              Turn the Computer Over
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board.
  • NOTE: Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You must make the appropriate changes again after you replace the system board.
  • NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can reconnect the cables correctly after you replace the system board.
  • CAUTION: Place the computer on a clean, flat surface.
  • Turn the computer over.

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board.

NOTE: Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You must make the appropriate changes again after you replace the system board.

NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can reconnect the cables correctly after you replace the system board.

CAUTION: Place the computer on a clean, flat surface.

Turn the computer over.

Step 55

              Disconnecting the Logo-Board Cable
  • Disconnect the logo-board cable from the system board.

Disconnect the logo-board cable from the system board.

Step 56

              Disconnecting the Power-Button Board Cable
  • Using the pull-tab, disconnect the power-button board cable from the system board.

Using the pull-tab, disconnect the power-button board cable from the system board.

Step 57

              Open the Latch
  • Open the latch and disconnect the display cable from the system board.

Open the latch and disconnect the display cable from the system board.

Step 58

              Turn the Computer Over
  • Turn the computer over.

Step 59

              Remove the Screw
  • Remove the screw (M2.5x6L) that secures the USB Type-C port bracket to the system board and lift the USB Type-C port bracket off the system board.

Remove the screw (M2.5x6L) that secures the USB Type-C port bracket to the system board and lift the USB Type-C port bracket off the system board.

Step 60

              Disconnecting the Power-Adapter Port
  • Disconnect the power-adapter port cable from the system board.

Disconnect the power-adapter port cable from the system board.

Step 61

              Disconnect the Speaker Cable
  • Disconnect the speaker cable from the system board.

Disconnect the speaker cable from the system board.

Step 62

              Open the Latch
  • Open the latch and disconnect the keyboard cable from the system board.

Open the latch and disconnect the keyboard cable from the system board.

Step 63

              Open the Latch
  • Open the latch and disconnect the keyboard-backlight cable from the system board.

Open the latch and disconnect the keyboard-backlight cable from the system board.

Step 64

              Disconnect the Touch-Pad Cable
  • Open the latch and disconnect the touch-pad cable from the system board.

Open the latch and disconnect the touch-pad cable from the system board.

Step 65

              Remove the Screw

Step 66

              Remove the two Screws
  • Remove the two screws (M2.5x6L) that secure the system board to the palm- rest assembly.

Remove the two screws (M2.5x6L) that secure the system board to the palm- rest assembly.

Step 67

              Lift the System Board
  • Lift the system board off the palm-rest assembly.

Lift the system board off the palm-rest assembly.

Step 68

              Align the Screw Holes
  • CAUTION: Ensure that no cables are under the system board.
  • Align the screw holes on the NEW system board with the screw holes on the palm- rest assembly.

CAUTION: Ensure that no cables are under the system board.

Align the screw holes on the NEW system board with the screw holes on the palm- rest assembly.

Step 69

              Replace the Two Screws
  • Replace the two screws (M2.5x6L) that secure the system-board to the palm- rest assembly.

Replace the two screws (M2.5x6L) that secure the system-board to the palm- rest assembly.

Step 70

              Align the Screw Hole
  • Align the screw hole on the USB Type-C port bracket with the screw hole on the system board on the back and right side of your computer.

Align the screw hole on the USB Type-C port bracket with the screw hole on the system board on the back and right side of your computer.

Step 71

              Replace the Screw
  • Replace the screw (M2.5x6L) that secures the USB Type-C port bracket to the system board on the back and right side of your computer.

Replace the screw (M2.5x6L) that secures the USB Type-C port bracket to the system board on the back and right side of your computer.

Step 72

              Slide the Touch-Pad Cable
  • Slide the touch-pad cable into the connector on the system board and close the latch to secure the cable.

Slide the touch-pad cable into the connector on the system board and close the latch to secure the cable.

Step 73

              Sliding the Keyboard-Backlight
  • Slide the keyboard-backlight cable into the connector on the system board and close the latch to secure the cable.

Slide the keyboard-backlight cable into the connector on the system board and close the latch to secure the cable.

Step 74

              Slide the Keyboard Cable
  • Slide the keyboard cable into the connector on the system board and close the latch to secure the cable.

Slide the keyboard cable into the connector on the system board and close the latch to secure the cable.

Step 75

              Connect the Speaker Cable
  • Connect the speaker cable to the system board.

Connect the speaker cable to the system board.

Step 76

              Connect the Power-Adapter
  • Connect the power-adapter port cable to the system board.

Connect the power-adapter port cable to the system board.

Step 77

              Turn the Computer Over

Step 78

              Slide the Display Cable
  • Slide the display cable into the connector on the system board and close the latch to secure the cable.

Slide the display cable into the connector on the system board and close the latch to secure the cable.

Step 79

              Connect the Power-Button Board Cable
  • Connect the power-button board cable to the system board.

Connect the power-button board cable to the system board.

Step 80

              Connect the Logo-Board Cable
  • Connect the logo-board cable to the system board.

Connect the logo-board cable to the system board.

Step 81

              Remove the Antenna Cables
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Remove the antenna cables from the routing guides on the palm-rest assembly.

Remove the antenna cables from the routing guides on the palm-rest assembly.

Step 82

              Remove the Logo-Board Cable
  • Remove the logo-board cable from the routing guides on the palm-rest assembly.

Remove the logo-board cable from the routing guides on the palm-rest assembly.

Step 83

              Remove the Display Cable
  • Remove the display cable from the routing guides on the palm-rest assembly.

Remove the display cable from the routing guides on the palm-rest assembly.

Step 84

              Turn the Computer Over
  • CAUTION: Place the computer on a clean, flat surface.
  • Turn the computer over.

Step 85

              Remove the Four Screws
  • Remove the four screws (M2.5x6L) that secure the display assembly to the palm-rest assembly.

Remove the four screws (M2.5x6L) that secure the display assembly to the palm-rest assembly.

Step 86

              Lifting the Display Assembly
  • Lift the display assembly off the palm-rest assembly.

Lift the display assembly off the palm-rest assembly.

Step 87

              Remove the Cables
  • Remove the cables from the routing holes on the palm-rest assembly.

Remove the cables from the routing holes on the palm-rest assembly.

Step 88

              Placing the Display
  • Place the display assembly on a clean, flat surface.

Place the display assembly on a clean, flat surface.

Step 89

              Route the Cables
  • Route the cables through the routing holes on the palm-rest assembly.

Route the cables through the routing holes on the palm-rest assembly.

Step 90

              Align the Screw Holes
  • Align the screw holes on the display hinges with the screw holes on the palm- rest assembly.

Align the screw holes on the display hinges with the screw holes on the palm- rest assembly.

Step 91

              Replace the Four Screws
  • Replace the four screws (M2.5x6L) that secure the display assembly to the palm-rest assembly.

Replace the four screws (M2.5x6L) that secure the display assembly to the palm-rest assembly.

Step 92

              Turn the Computer Over

Step 93

              Route the Logo-Board Cable
  • Route the logo-board cable through the routing guides on the palm-rest assembly.

Route the logo-board cable through the routing guides on the palm-rest assembly.

Step 94

              Route the Antenna Cables
  • Route the antenna cables through the routing guides on the palm-rest assembly.

Route the antenna cables through the routing guides on the palm-rest assembly.

Step 95

              Prying the Inside Edges
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Using your fingertips, carefully pry up the inside edges of the display bezel.

Using your fingertips, carefully pry up the inside edges of the display bezel.

Step 96

              Lift the Display Bezel
  • Carefully lift the display bezel and turn it over.

Carefully lift the display bezel and turn it over.

Step 97

              Disconnect the Alien Head Logo
  • Open the latch and disconnect the alien head logo-board cable from the logo board.

Open the latch and disconnect the alien head logo-board cable from the logo board.

Step 98

              Peeling the Tape
  • Peel off the tape that secures the logo-board cable to the logo board and disconnect the logo-board cable from the logo board.

Peel off the tape that secures the logo-board cable to the logo board and disconnect the logo-board cable from the logo board.

Step 99

              Lift the Display Bezel
  • Lift the display bezel off the display assembly.

Lift the display bezel off the display assembly.

Step 100

              Place the Display Assembly
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Place the display assembly on a clean and flat surface.

Place the display assembly on a clean and flat surface.

Step 101

              Connect the Logo-Board
  • Connect the logo-board cable to the logo board.

Connect the logo-board cable to the logo board.

Step 102

              Adhering the Tape
  • Adhere the tape that secures the logo-board cable to the logo board.

Adhere the tape that secures the logo-board cable to the logo board.

Step 103

              Slide the Logo Board Cable
  • Slide the alien head logo-board cable into the logo board and close the latch to secure the cable.

Slide the alien head logo-board cable into the logo board and close the latch to secure the cable.

Step 104

              Turn the Display Bezel Over
  • Carefully turn the display bezel over.

Carefully turn the display bezel over.

Step 105

              Align the Bezel
  • Align the display bezel with the display back-cover and antenna assembly and gently snap the display bezel into place.

Align the display bezel with the display back-cover and antenna assembly and gently snap the display bezel into place.

Step 106

              Pry the Camera Module
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Using a plastic scribe, pry the camera module from the display back-cover and antenna assembly.

Using a plastic scribe, pry the camera module from the display back-cover and antenna assembly.

Step 107

              Peel the Tape
  • Peel the tape that secures the camera cable to the camera module and disconnect the camera cable from the camera module.

Peel the tape that secures the camera cable to the camera module and disconnect the camera cable from the camera module.

Step 108

              Lift the Camera Module
  • Lift the camera module from the display back-cover and antenna assembly.

Lift the camera module from the display back-cover and antenna assembly.

Step 109

              Adhere the Camera Module
  • Using the alignment posts, adhere the NEW camera module to the display back-cover and antenna assembly.

Using the alignment posts, adhere the NEW camera module to the display back-cover and antenna assembly.

Step 110

              Connect the Camera Cable
  • Connect the camera cable to the camera module.

Connect the camera cable to the camera module.

Step 111

              Adhere the Tape
  • Adhere the tape that secures the camera cable to the camera module.

Adhere the tape that secures the camera cable to the camera module.

Step 112

              Remove the Screws
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Remove the four screws (M1.6x2) that secure the display panel to the display back-cover and antenna assembly.

Remove the four screws (M1.6x2) that secure the display panel to the display back-cover and antenna assembly.

Step 113

              Lift the Display Panel
  • Gently lift the display panel and turn it over.

Gently lift the display panel and turn it over.

Step 114

              Peel the Tape
  • Peel the tape that secures the display cable to the display panel.

Peel the tape that secures the display cable to the display panel.

Step 115

              Open the Latch
  • Open the latch and disconnect the display cable from the display panel.

Open the latch and disconnect the display cable from the display panel.

Step 116

  • Lift the display panel off the display back-cover.

Lift the display panel off the display back-cover.

Step 117

              Slide the Display Cable
  • Slide the display cable into the connector on the NEW display panel and close the latch to secure the cable.

Slide the display cable into the connector on the NEW display panel and close the latch to secure the cable.

Step 118

  • Adhere the tape that secures the display cable to the display panel.

Adhere the tape that secures the display cable to the display panel.

Step 119

              Turn the Display Panel Over
  • Turn the display panel over and gently place it on the display back-cover.
  • CAUTION: Ensure that no cables are under the display panel.

Turn the display panel over and gently place it on the display back-cover.

CAUTION: Ensure that no cables are under the display panel.

Step 120

              Align the Screw Holes
  • Align the screw holes on the display panel with the screw holes on the display back-cover and antenna assembly.

Align the screw holes on the display panel with the screw holes on the display back-cover and antenna assembly.

Step 121

              Replace the Four Screws
  • Replace the four screws (M1.6x2) that secure the display panel to the display back-cover and antenna assembly.

Replace the four screws (M1.6x2) that secure the display panel to the display back-cover and antenna assembly.

Step 122

              Press the Hinge Caps
  • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  • Press the hinge caps on both the edges to release the hinge caps from the hinge.

Press the hinge caps on both the edges to release the hinge caps from the hinge.

Step 123

              Remove the Hinge Caps
  • Remove the hinge caps off the hinges.

Remove the hinge caps off the hinges.

Step 124

              Remove the Display Cable
  • Remove the display cable from the routing guide on the display back-cover and antenna assembly.

Remove the display cable from the routing guide on the display back-cover and antenna assembly.

Step 125

              Remove the Logo-Board Cable
  • Remove the logo-board cable from the routing guide on the display back-cover and antenna assembly.

Remove the logo-board cable from the routing guide on the display back-cover and antenna assembly.

Step 126

              Remove the Antenna Cables
  • Remove the antenna cables from the routing guide on the display back-cover and antenna assembly.

Remove the antenna cables from the routing guide on the display back-cover and antenna assembly.

Step 127

              Remove the Right Screws
  • Remove the eight screws (M2.5x2.0L) that secure the hinges to the display back-cover and antenna assembly.

Remove the eight screws (M2.5x2.0L) that secure the hinges to the display back-cover and antenna assembly.

Step 128

              Lift the Hinges
  • Lift the hinges from the display back-cover and antenna assembly.

Lift the hinges from the display back-cover and antenna assembly.

Step 129

              Align the Screw Holes
  • Align the screw holes on the NEW display hinges with the screw holes on the display back-cover and antenna assembly.

Align the screw holes on the NEW display hinges with the screw holes on the display back-cover and antenna assembly.

Step 130

              Replace the Eight Screws
  • Replace the eight screws (M2.5x2.0L) that secure the display hinges to the display back-cover and antenna assembly.

Replace the eight screws (M2.5x2.0L) that secure the display hinges to the display back-cover and antenna assembly.

Step 131

              Route the Antenna Cables
  • Route the antenna cables through the routing guides on the display back-cover and antenna assembly.

Route the antenna cables through the routing guides on the display back-cover and antenna assembly.

Step 132

              Route the Logo-Board Cable
  • Route the logo-board cable through the routing guides on the display back-cover and antenna assembly.

Route the logo-board cable through the routing guides on the display back-cover and antenna assembly.

Step 133

              Route the Display Cable
  • Route the display cable through the routing guides on the display back-cover and antenna assembly.

Route the display cable through the routing guides on the display back-cover and antenna assembly.

Step 134

              Place the Hinge Caps
  • Place the hinge caps on the display hinges and press down to snap them into place.

Place the hinge caps on the display hinges and press down to snap them into place.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Terrence15

Member since: 12/18/2017

78,526 Reputation

                                      441 Guides authored                  



                       Badges:
                       28







                                                        +25 more badges

Team

                       Informative Technologies Inc.                        

                                                  Member of Informative Technologies Inc. 



                    Community                     


                                            38 Members                     


                                            1,980 Guides authored