Difficulty

Difficult

Steps

26

Time Required

                          50 minutes - 1 hour

Sections

3

  • Base Panel
  • 3 steps
  • Computer Base
  • 21 steps
  • Heat-sink Assembly
  • 2 steps

Flags

0

  • BackDell Alienware 13

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Base Panel
  • Working on an electrical device while plugged in can cause injury due to electrical shock. Ensure that all external power is disconnected from the device.
  • Close the device and turn the device over.

Working on an electrical device while plugged in can cause injury due to electrical shock. Ensure that all external power is disconnected from the device.

Close the device and turn the device over.

1024

Step 2

  • Remove (2) 5 mm Phillips head screws attaching the small access panel to the base using a Phillips # 1 screwdriver.
  • The (2) screws are attached to the base panel with retaining clips and won’t completely detach from the panel.

Remove (2) 5 mm Phillips head screws attaching the small access panel to the base using a Phillips # 1 screwdriver.

The (2) screws are attached to the base panel with retaining clips and won’t completely detach from the panel.

Step 3

  • Remove the small access panel using a heavy duty spudger.

Remove the small access panel using a heavy duty spudger.

Step 4

              Computer Base
  • Disconnect the battery cable from the battery cable terminal.

Disconnect the battery cable from the battery cable terminal.

Step 5

  • Remove (4) 6 mm Phillips head screws from the solid-state metal drive bracket, using a Phillips # 1 screwdriver.

Remove (4) 6 mm Phillips head screws from the solid-state metal drive bracket, using a Phillips # 1 screwdriver.

Step 6

  • Grab the pull tab to pivot the solid-state drive bracket upwards. Remove the bracket from the computer base.

Grab the pull tab to pivot the solid-state drive bracket upwards. Remove the bracket from the computer base.

Step 7

  • Using the pull tab, disconnect the black solid-state drive cable from the system board.

Using the pull tab, disconnect the black solid-state drive cable from the system board.

Step 8

  • Remove (2) 3 mm Phillips head screws, using a Phillips # 0 screwdriver, that connect the solid-state drive assembly to the computer base.

Remove (2) 3 mm Phillips head screws, using a Phillips # 0 screwdriver, that connect the solid-state drive assembly to the computer base.

Step 9

  • Lift up on the solid-state drive assembly to remove it from the computer base.

Lift up on the solid-state drive assembly to remove it from the computer base.

Step 10

  • Locate two cables labeled, “KB Backlight” (orange) and “KB Membrane” (black). Lift up on the latches to disconnect the cables from the system board.
  • The latches that connect the cables to the system board are very delicate. Handle with care to avoid damaging them.

Locate two cables labeled, “KB Backlight” (orange) and “KB Membrane” (black). Lift up on the latches to disconnect the cables from the system board.

The latches that connect the cables to the system board are very delicate. Handle with care to avoid damaging them.

Step 11

  • Remove (8) 9 mm Phillips head screws using a Phillips # 1 screwdriver, that secures the palm-rest assembly to the computer base.
  • Remove (4) 8 mm Phillips head screws using a Phillips # 1 screwdriver.
  • Remove (2) 7 mm Phillips head screws using a Phillips # 1 screwdriver.

Remove (8) 9 mm Phillips head screws using a Phillips # 1 screwdriver, that secures the palm-rest assembly to the computer base.

Remove (4) 8 mm Phillips head screws using a Phillips # 1 screwdriver.

Remove (2) 7 mm Phillips head screws using a Phillips # 1 screwdriver.

Step 12

  • Lift the computer base slightly towards you and push the release tabs on the palm-rest assembly until it pops out using a spudger.

Lift the computer base slightly towards you and push the release tabs on the palm-rest assembly until it pops out using a spudger.

Step 13

  • Turn the computer over and open the display as far as possible.
  • Using a plastic spudger, pry up along the edges of the palm-rest assembly.
  • Gently lift the palm-rest assembly.

Turn the computer over and open the display as far as possible.

Using a plastic spudger, pry up along the edges of the palm-rest assembly.

Gently lift the palm-rest assembly.

Step 14

  • Lift the connector latch and disconnect the power-button board cable from the system board. Identified as a cable with a blue tab.
  • Lift the palm-rest assembly off the computer base.

Lift the connector latch and disconnect the power-button board cable from the system board. Identified as a cable with a blue tab.

Lift the palm-rest assembly off the computer base.

Step 15

  • Open the display as far as possible.
  • Remove (2) 3 mm Phillips head screws, using a Phillips head #0 screwdriver, that secure the hinge caps to the display hinges.
  • Slide and lift the hinge caps off the display hinges.

Open the display as far as possible.

Remove (2) 3 mm Phillips head screws, using a Phillips head #0 screwdriver, that secure the hinge caps to the display hinges.

Slide and lift the hinge caps off the display hinges.

Step 16

  • Close the display and turn the computer over.
  • Remove (1) 2 mm Phillips head screw, using a Phillips head # 0 screwdriver, that secures the wireless-card bracket to the wireless card.

Close the display and turn the computer over.

Remove (1) 2 mm Phillips head screw, using a Phillips head # 0 screwdriver, that secures the wireless-card bracket to the wireless card.

Step 17

  • Disconnect the antenna cables from the wireless card using a heavy duty spudger. The wires can be removed by applying a force directed upward, away from the device.

Disconnect the antenna cables from the wireless card using a heavy duty spudger. The wires can be removed by applying a force directed upward, away from the device.

Step 18

  • Turn the computer over and open the display.
  • Peel off the adhesive tapes that secure the antenna cables to the system board.
  • Make note of how the cables are routed before removing any cables from their routing guide.

Turn the computer over and open the display.

Peel off the adhesive tapes that secure the antenna cables to the system board.

Make note of how the cables are routed before removing any cables from their routing guide.

Step 19

  • Lift the connector latch and disconnect the display cable from the system board.
  • Disconnect the logo-board cable from the system board.
  • Remove the antenna cables, display cable, and logo-board cable from the routing guides on the display hinges.

Lift the connector latch and disconnect the display cable from the system board.

Disconnect the logo-board cable from the system board.

Remove the antenna cables, display cable, and logo-board cable from the routing guides on the display hinges.

Step 20

  • Remove (4) 8 mm Phillips head screws, using a Phillips # 1 screwdriver, that secure the display assembly to the computer base.
  • Lift the display assembly off the computer base.

Remove (4) 8 mm Phillips head screws, using a Phillips # 1 screwdriver, that secure the display assembly to the computer base.

Lift the display assembly off the computer base.

Step 21

  • Remove the (2) 6 mm Phillips head screws securing the power adapter port bracket with a #1 Phillips screwdriver.
  • Lift and remove the power adapter port bracket.

Remove the (2) 6 mm Phillips head screws securing the power adapter port bracket with a #1 Phillips screwdriver.

Lift and remove the power adapter port bracket.

Step 22

  • Lift up and remove the power adapter port from the computer base.

Lift up and remove the power adapter port from the computer base.

Step 23

  • Disconnect the speaker cable connector from the service board.

Disconnect the speaker cable connector from the service board.

Step 24

  • Remove (3) 6 mm Phillips head screws securing the service board with a #1 Phillips screwdriver.
  • Lift up on the service board assembly using a heavy duty spudger and slide the board towards the battery to remove from the base.

Remove (3) 6 mm Phillips head screws securing the service board with a #1 Phillips screwdriver.

Lift up on the service board assembly using a heavy duty spudger and slide the board towards the battery to remove from the base.

Step 25

              Heat-sink Assembly
  • The heat-sink assembly can get very hot during computer use. Let the computer cool off before touching the heat-sink assembly.
  • Oils from hands can reduce the efficiency of the heat transfer capabilities. Avoid direct contact with the heat transfer areas as much as possible.
  • Disconnect (2) fan cables attaching the fans to the motherboard.

The heat-sink assembly can get very hot during computer use. Let the computer cool off before touching the heat-sink assembly.

Oils from hands can reduce the efficiency of the heat transfer capabilities. Avoid direct contact with the heat transfer areas as much as possible.

Disconnect (2) fan cables attaching the fans to the motherboard.

Step 26

  • Turn the system board over.
  • Remove the (7) 3 mm Phillips head screws attaching the heat-sink assembly to the system board with a #0 Phillips screwdriver.
  • Lift up and remove the heat-sink assembly.

Turn the system board over.

Remove the (7) 3 mm Phillips head screws attaching the heat-sink assembly to the system board with a #0 Phillips screwdriver.

Lift up and remove the heat-sink assembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor 


                    Adam Russell

Member since: 09/26/2016

898 Reputation

                                      6 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges

Team

                       USF Tampa, Team 14-2, Eyestone Fall 2016                        

                                                  Member of USF Tampa, Team 14-2, Eyestone Fall 2016 



                    USFT-EYESTONE-F16S14G2                     


                                            3 Members                     


                                            7 Guides authored