Difficulty

Moderate

Steps

11

Time Required

                          30 - 45 minutes

Sections

1

  • Speaker
  • 11 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackDefinitive Technology W7

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Speaker
  • Use the metal spudger to pry off the panel at the top of the device.
  • The top panel has the device logo in the center.
  • Use the flat end of the metal spudger and place it between the gaps of the top panel and slowly pry the panel off.

Use the metal spudger to pry off the panel at the top of the device.

The top panel has the device logo in the center.

Use the flat end of the metal spudger and place it between the gaps of the top panel and slowly pry the panel off.

1024

Step 2

  • Remove the thirteen Phillips #0 screws.

Remove the thirteen Phillips #0 screws.

Step 3

  • Remove the black panel.

Remove the black panel.

Step 4

  • After you remove the black panel, you will see that the device is covered with a gray mesh, secured with a drawstring.
  • Flick the switch on the middle of the lock down to loosen the sack.

After you remove the black panel, you will see that the device is covered with a gray mesh, secured with a drawstring.

Flick the switch on the middle of the lock down to loosen the sack.

Step 5

  • After you have flicked the switch loosen the sack and pull the sack down which will reveal the speaker.

After you have flicked the switch loosen the sack and pull the sack down which will reveal the speaker.

Step 6

  • Remove the four screws on top of the device on each corner with a Phillips #0 screwdriver.

Remove the four screws on top of the device on each corner with a Phillips #0 screwdriver.

Step 7

  • Gently lift the top cover off the device.

Gently lift the top cover off the device.

Step 8

  • If you now look inside the device, you will see the speaker which is the large cylinder on the inner side of the device.

If you now look inside the device, you will see the speaker which is the large cylinder on the inner side of the device.

Step 9

  • Remove the four Phillips #0 screws around the speaker holding it in place.
  • Now lay the device on its side with the speaker facing upward, then unscrew the screws around the speaker.

Remove the four Phillips #0 screws around the speaker holding it in place.

Now lay the device on its side with the speaker facing upward, then unscrew the screws around the speaker.

Step 10

  • Stand the device upright and carefully pull the speaker out of the device with the wires still intact.

Stand the device upright and carefully pull the speaker out of the device with the wires still intact.

Step 11

  • Now grab the end of the wire connecting the device to the speaker itself.
  • Slowly and carefully pull the wires away from the speaker.

Now grab the end of the wire connecting the device to the speaker itself.

Slowly and carefully pull the wires away from the speaker.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Jamari Brewster

Member since: 10/26/2022

193 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       UMass Dartmouth, Team 2-5, Petersen Fall 2022                        

                                                  Member of UMass Dartmouth, Team 2-5, Petersen Fall 2022 



                    UMASSD-PETERSEN-F22S2G5                     


                                            4 Members                     


                                            5 Guides authored