Difficulty

Moderate

Steps

8

Time Required

                          45 minutes

Sections

4

  • Top Cover
  • 2 steps
  • Motherboard and LED Bulb
  • 3 steps
  • Power Supply Circuit
  • 2 steps
  • Lens
  • 1 step

Flags

0

  • BackDBPOWER RD-810

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Top Cover
  • Make sure the projector is unplugged before starting
  • Place the projector upside down to access the screws on the bottom.
  • Remove the five 7mm long screws using a #3 Phillips screwdriver at least 2 inches long.

Make sure the projector is unplugged before starting

Place the projector upside down to access the screws on the bottom.

Remove the five 7mm long screws using a #3 Phillips screwdriver at least 2 inches long.

1024

Step 2

  • Flip the projector over and then remove the cover by lifting it up.

Flip the projector over and then remove the cover by lifting it up.

Step 3

              Motherboard and LED Bulb
  • Remove the three 6mm PH2 phillips head screws.
  • Disconnect the ribbon cable by flipping up the latch on the connector and then pull the ribbon out.

Remove the three 6mm PH2 phillips head screws.

Disconnect the ribbon cable by flipping up the latch on the connector and then pull the ribbon out.

Step 4

  • Disconnect the three wire connectors. Grasp both sides of the connector and pull apart.
  • Keep the connector parallel to the mother board to avoid breaking the solder connection.
  • Lift the motherboard up and place it out of the way.

Disconnect the three wire connectors. Grasp both sides of the connector and pull apart.

Keep the connector parallel to the mother board to avoid breaking the solder connection.

Lift the motherboard up and place it out of the way.

Step 5

  • Remove the five 7mm PH2 phillips head screws on the black plate and lift the plate out.
  • Lift the aluminum heat sink up to remove it from the projector.
  • The motherboard is already removed in this step.

Remove the five 7mm PH2 phillips head screws on the black plate and lift the plate out.

Lift the aluminum heat sink up to remove it from the projector.

The motherboard is already removed in this step.

Step 6

              Power Supply Circuit
  • Remove the two 9mm PH2 phillips head screws.
  • Lift the mirror behind the power supply circuit out to gain access to the circuit board.

Remove the two 9mm PH2 phillips head screws.

Lift the mirror behind the power supply circuit out to gain access to the circuit board.

Step 7

  • Lift the power supply circuit board out of the projector.
  • Disconnect the cable connector by pulling the two sides of the connector apart.
  • Keep the connector parallel to the circuit board to avoid breaking the solder connection.

Lift the power supply circuit board out of the projector.

Disconnect the cable connector by pulling the two sides of the connector apart.

Keep the connector parallel to the circuit board to avoid breaking the solder connection.

Step 8

              Lens
  • Flip the projector over and remove the two 6mm PH2 phillips head screws.
  • Flip the projector over so that the opening is facing up.
  • Lift the lens up slightly and then move it towards the interior of the projector before lifting it up and out of the way.

Flip the projector over and remove the two 6mm PH2 phillips head screws.

Flip the projector over so that the opening is facing up.

Lift the lens up slightly and then move it towards the interior of the projector before lifting it up and out of the way.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor 


                    John Russell

Member since: 02/14/2018

836 Reputation

                                      9 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       USF Tampa, Team S5-G3, Eyestone Spring 2018                        

                                                  Member of USF Tampa, Team S5-G3, Eyestone Spring 2018 



                    USFT-EYESTONE-S18S5G3                     


                                            3 Members                     


                                            9 Guides authored