Difficulty
Moderate
Steps
10
Time Required
5 minutes
Sections
2
- Logic Board
- 6 steps
- LED Light
- 4 steps
Flags
1
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
BackD-Link EBR-2310
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Remove Plastic Screw Coverings
- Begin by placing the wired router face down.
- Locate the two black plastic screw coverings at the top of the device and remove them with your fingers.
- The two bottom plastic screw coverings do not need to be taken off.
Begin by placing the wired router face down.
Locate the two black plastic screw coverings at the top of the device and remove them with your fingers.
The two bottom plastic screw coverings do not need to be taken off.
1024
Step 2
Remove Screws
- Using a Philips PH2 screwdriver head, unscrew the two top screws.
Using a Philips PH2 screwdriver head, unscrew the two top screws.
Step 3
Pry Open The Router
- Using a plastic opening tool, trace the edges of the router on all sides. Gently pry the device until it eventually snaps open.
Using a plastic opening tool, trace the edges of the router on all sides. Gently pry the device until it eventually snaps open.
Step 4
Remove Silver Casing
- Once you have removed the top black case of the router, remove the silver casing surrounding the logic board.
- It should easily snap out of place.
Once you have removed the top black case of the router, remove the silver casing surrounding the logic board.
It should easily snap out of place.
Step 5
Remove Inner Bottom Screws
- Locate the two screws at the bottom of the logic board.
- Using the same PH2 head on your Philips screwdriver, unscrew these screws.
Locate the two screws at the bottom of the logic board.
Using the same PH2 head on your Philips screwdriver, unscrew these screws.
Step 6
Remove Bottom Case
- Now that you have removed all screws and the surrounding silver casing, pop the logic board out from the bottom component of the router.
- You have now removed the logic board from your device.
Now that you have removed all screws and the surrounding silver casing, pop the logic board out from the bottom component of the router.
You have now removed the logic board from your device.
Step 7
Locate Problematic LED light
- Locate the problematic LED light on the motherboard.
- Using a plastic opening tool, very gently tilt its black base backwards.
Locate the problematic LED light on the motherboard.
Using a plastic opening tool, very gently tilt its black base backwards.
Step 8
Continue Readjusting LED Light Base
- Using your soft finger, tilt the LED light base backwards so that the actual light is facing upside down, at a 180 degree angle from the others.
Using your soft finger, tilt the LED light base backwards so that the actual light is facing upside down, at a 180 degree angle from the others.
Step 9
Remove the LED Light
- With a pair of tweezers, gently pry the LED light back and forth between its connecting wires until it is able to be removed.
With a pair of tweezers, gently pry the LED light back and forth between its connecting wires until it is able to be removed.
Step 10
Complete Removal
- You should now have a removed LED light, ready to be replaced with a new one.
You should now have a removed LED light, ready to be replaced with a new one.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Jessica
Member since: 09/19/2014
428 Reputation
3 Guides authored
Badges:
6
+3 more badges
Team
USF Sarasota-Manatee, Team 1-4, Stewart Fall 2014
Member of USF Sarasota-Manatee, Team 1-4, Stewart Fall 2014
USFSM-STEWART-F14S1G4
4 Members
16 Guides authored
