Cuisinart Dfp 14Bcn Power Cord Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          15 - 25 minutes

Sections

Bowl
5 steps
Back Casing
4 steps
Power Cord
3 steps

Flags

BackCuisinart DFP-14BCN
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Bowl

Unplug your food processor before starting any disassembly.
Remove the small pusher by rotating it clockwise and lifting up.

Unplug your food processor before starting any disassembly.

Remove the small pusher by rotating it clockwise and lifting up.

1024

Step 2

Remove the large pusher by grabbing its sides and pulling up.
There may be a clicking sound from the safety feature being disengaged in this step.

Remove the large pusher by grabbing its sides and pulling up.

There may be a clicking sound from the safety feature being disengaged in this step.

Step 3

Remove the lid from the bowl by turning it clockwise and lifting.

Remove the lid from the bowl by turning it clockwise and lifting.

Step 4

Take out the blades by grabbing the plastic center piece and lifting up.
Avoid contact with blades as they are extremely sharp.

Take out the blades by grabbing the plastic center piece and lifting up.

Avoid contact with blades as they are extremely sharp.

Step 5

Position the handle of the bowl so that it is on your left.
Grab the handle and push clockwise. Lift up the bowl to remove it.

Position the handle of the bowl so that it is on your left.

Grab the handle and push clockwise. Lift up the bowl to remove it.

Step 6

              Back Casing

Turn the food processor’s base upside down by lifting it up and turning it over.
Position the base so that the on and pulse buttons are facing you.
Place the base on top of the food processor’s bowl to keep the base from wobbling while you work on it.

Turn the food processor’s base upside down by lifting it up and turning it over.

Position the base so that the on and pulse buttons are facing you.

Place the base on top of the food processor’s bowl to keep the base from wobbling while you work on it.

Step 7

Remove the two 13.0mm screws that hold down the casing with a Phillips #2 screwdriver.

Remove the two 13.0mm screws that hold down the casing with a Phillips #2 screwdriver.

Step 8

Lift up the front left and the back right rubber feet by pulling back the rubber with your fingers.
Remove the 13.0mm screw under each rubber foot with a Phillips #2 screwdriver.

Lift up the front left and the back right rubber feet by pulling back the rubber with your fingers.

Remove the 13.0mm screw under each rubber foot with a Phillips #2 screwdriver.

Step 9

Lift off the back casing by raising it upward.

Lift off the back casing by raising it upward.

Step 10

              Power Cord

Unlatch the power cord from its casing at the bottom left corner of the base by lifting the cord upward.

Unlatch the power cord from its casing at the bottom left corner of the base by lifting the cord upward.

Step 11

Use flat pliers to clamp down on the wide part of the plastic covering located at the power cord’s white wire connection.
Pull the plastic cover off of the wire by keeping the pliers clamped down and pulling away from the wires.
This may require some force.
Repeat for the power cord’s brown wire connection.

Use flat pliers to clamp down on the wide part of the plastic covering located at the power cord’s white wire connection.

Pull the plastic cover off of the wire by keeping the pliers clamped down and pulling away from the wires.

This may require some force.

Repeat for the power cord’s brown wire connection.

Step 12

Use wire cutters to cut the exposed wire on the power cord’s white wire. To cut the wire, position the blades of the wire cutter over the exposed wire and clamp down.
Repeat for the power cord’s brown wire connection. This cuts off the connection between the power cord and motor.
Pull the power cord out. It is no longer attached to the device.
For reassembly, the wires will need to be soldered together. Check out this soldering guide for instructions.

Use wire cutters to cut the exposed wire on the power cord’s white wire. To cut the wire, position the blades of the wire cutter over the exposed wire and clamp down.

Repeat for the power cord’s brown wire connection. This cuts off the connection between the power cord and motor.

Pull the power cord out. It is no longer attached to the device.

For reassembly, the wires will need to be soldered together. Check out this soldering guide for instructions.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Vanessa See

Member since: 10/06/2016

125 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 10-3, Livingston Fall 2016                        

                                                  Member of Cal Poly, Team 10-3, Livingston Fall 2016 



                    CPSU-LIVINGSTON-F16S10G3                     


                                            3 Members                     


                                            7 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team