Cuisinart Dcc 1200 Toggle Switch Replacement Repair Guide

Difficulty

Moderate

Steps

8

Time Required

                          25 minutes            

Sections

1

• Toggle Switch
• 8 steps

Flags

0

• BackCuisinart DCC-1200

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Toggle Switch               

• Using the metal spudger, gently pry out the two plastic plugs located on top.
• Too much pressure with the spudger may cause damage to plugs.

Using the metal spudger, gently pry out the two plastic plugs located on top.

Too much pressure with the spudger may cause damage to plugs.

1024

Step 2

• Remove the two 11 mm long screws from the top of the coffee maker underneath the cover using the bit driver with the extension with the PH1 Phillips bit.

Remove the two 11 mm long screws from the top of the coffee maker underneath the cover using the bit driver with the extension with the PH1 Phillips bit.

Step 3

• Once the screws are removed, take the coffee maker face plate off by pulling it down and away from the rest of the coffee maker.
• Use care when handling the face plate once it is removed from the rest of the coffee maker as the electrical connection is still intact.

Once the screws are removed, take the coffee maker face plate off by pulling it down and away from the rest of the coffee maker.

Use care when handling the face plate once it is removed from the rest of the coffee maker as the electrical connection is still intact.

Step 4

• Remove the electrical connection to the circuit board by carefully removing the connection by pulling straight up and away from the circuit board.
• Once the electrical connection is removed, separate the face plate from the rest of the coffee maker.

Remove the electrical connection to the circuit board by carefully removing the connection by pulling straight up and away from the circuit board.

Once the electrical connection is removed, separate the face plate from the rest of the coffee maker.

Step 5

• Use the bit driver with the PH1 Philips bit to remove the three 11 mm long screws holding the circuit board to the face plate.
• Once the circuit board screws are removed, carefully remove the circuit board from the face plate revealing the inside of the face plate.

Use the bit driver with the PH1 Philips bit to remove the three 11 mm long screws holding the circuit board to the face plate.

Once the circuit board screws are removed, carefully remove the circuit board from the face plate revealing the inside of the face plate.

Step 6

• Remove the four 10 mm long screws with the bit driver with the PH1 Phillips bit driver from the toggle switch plate.
• Once the screws are removed, remove the toggle switch plate from the face plate.

Remove the four 10 mm long screws with the bit driver with the PH1 Phillips bit driver from the toggle switch plate.

Once the screws are removed, remove the toggle switch plate from the face plate.

Step 7

• Remove the hex nut from behind the toggle switch on the front of the face plate.

Remove the hex nut from behind the toggle switch on the front of the face plate.

Step 8

• Remove toggle switch by pulling it out from inside the face plate.

Remove toggle switch by pulling it out from inside the face plate.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.                                             

Author

                                      with 5 other contributors 

                    Lauren Miller                     

Member since: 02/15/2018

412 Reputation

                                      1 Guide authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       UW Stout, Team S8-G1, Ogden Spring 2018                        

                                                  Member of UW Stout, Team S8-G1, Ogden Spring 2018 



                    UWSTOUT-OGDEN-S18S8G1                     


                                            4 Members                     


                                            5 Guides authored                     

Daniel Thaler - Nov 3, 2018

Reply

It seems to me that the defective part would be the switch plate, not the switch itself. Where would one get replacement parts?

Anne Crawford - Jan 29, 2019

Reply

Where do I get the new toggle switch?

Paul Patterson - Oct 19, 2020

Reply

Pretty clear instructions. The only thing missing is the responses to the previous two questions.

Renee Schultz - Jul 14, 2021

Reply

Very nice instructions. However without a part number they are useless.

Pat Day - Dec 12, 2021

Reply

The only problem is that the faceplate on mine seemed to be very solidly glued (maybe silicone sealant) in place.

It resisted every effort to budge down and outwards, as indicated here. Adding more pressures, noi matter how carefully, resulted in a warped cover -followed by an order for a replacement Cuisinart, same model, as I still believe this is the best in the market.