Crock Pot Express Crock Multi Cooker Heating Element Replacement Repair Guide

Difficulty

Moderate

Steps

13

Time Required

                          45 minutes            

Sections

3

• Power Cord
• 3 steps
• Lid
• 1 step
• Heating Element
• 9 steps

Flags

0

• BackCrock-Pot Express Crock Multi-Cooker

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Power Cord               

• Remove the power cord from the wall outlet first, disconnecting power from the device.

Remove the power cord from the wall outlet first, disconnecting power from the device.

1024

Step 2

• Orient the device with with the LED facing away from the user allowing access to the input jack of the power cord.

Orient the device with with the LED facing away from the user allowing access to the input jack of the power cord.

Step 3

• Grasp the power cord input connector firmly with forefinger and thumb.
• Without tugging, apply pulling force until the connector is free from device

Grasp the power cord input connector firmly with forefinger and thumb.

Without tugging, apply pulling force until the connector is free from device

Step 4

              Lid               

• Orient the crock pot where the lid locked and unlocked icons are visible.
• Grasp the handle firmly and turn the lid clockwise until the arrow and the lid unlocked icon are facing each other.
• Remove the lid.

Orient the crock pot where the lid locked and unlocked icons are visible.

Grasp the handle firmly and turn the lid clockwise until the arrow and the lid unlocked icon are facing each other.

Remove the lid.

Step 5

              Heating Element               

• Remove the inner pot and set it aside for reassembly.

Remove the inner pot and set it aside for reassembly.

Step 6

• Carefully rotate the Crock-Pot so that the bottom is facing upward, allowing access to the electrical panel.
• Remove the two 12.4 mm screws with a Phillips #2 screwdriver.

Carefully rotate the Crock-Pot so that the bottom is facing upward, allowing access to the electrical panel.

Remove the two 12.4 mm screws with a Phillips #2 screwdriver.

Step 7

• Rotate the electrical panel cover counter clockwise and pull up until the panel comes free.

Rotate the electrical panel cover counter clockwise and pull up until the panel comes free.

Step 8

• Remove 3 nuts, 3 washers, 3 spacers, and 3 lock washers using an adjustable wrench to free the heating element from the Crock-Pot housing.

Remove 3 nuts, 3 washers, 3 spacers, and 3 lock washers using an adjustable wrench to free the heating element from the Crock-Pot housing.

Step 9

• Remove the 10mm screw and metal plate beneath the electrical nodes using a Phillips #2 screwdriver.

Remove the 10mm screw and metal plate beneath the electrical nodes using a Phillips #2 screwdriver.

Step 10

• Remove the 2 red wires from the terminal post by unscrewing the 10mm screw using a Phillips #2 screwdriver and label terminal post as red.
• Remove 1 white wire from terminal post by unscrewing the 10mm screw using a Phillips #2 screwdriver and label terminal post as white.

Remove the 2 red wires from the terminal post by unscrewing the 10mm screw using a Phillips #2 screwdriver and label terminal post as red.

Remove 1 white wire from terminal post by unscrewing the 10mm screw using a Phillips #2 screwdriver and label terminal post as white.

Step 11

• Reorient the crockpot on its side to prepare for the heating element removal.

Reorient the crockpot on its side to prepare for the heating element removal.

Step 12

• Carefully pull the heating element out and rotate it until bottom side is facing up out of the pot.

Carefully pull the heating element out and rotate it until bottom side is facing up out of the pot.

Step 13

• Remove both 19mm screws from the cutout switch housing using a Phillips #2 screwdriver, freeing the heating element from the device.
• Carefully remove the heating element from the device.

Remove both 19mm screws from the cutout switch housing using a Phillips #2 screwdriver, freeing the heating element from the device.

Carefully remove the heating element from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    William Kelly                     

Member since: 09/24/2018

742 Reputation

                                      7 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       The Citadel Military College of South Carolina, Team S3-G9, Eggleston Fall 2018                        

                                                  Member of The Citadel Military College of South Carolina, Team S3-G9, Eggleston Fall 2018 



                    CMCSC-EGGLESTON-F18S3G9                     


                                            4 Members                     


                                            7 Guides authored