Difficulty

Moderate

Steps

10

Time Required

                          15 - 20 minutes

Sections

3

  • Light Bulb
  • 3 steps
  • Sliding Lock Mechanism
  • 3 steps
  • White Plastic Arm inside the Control Box
  • 4 steps

Flags

0

  • BackCrayola Crayon Maker

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Take out the melting tray that is out of place.
  • Press the green arm away from the melting tray. Remove the melting tray.
  • Pop the metal arms out of the green pivot support.

Press the green arm away from the melting tray. Remove the melting tray.

Pop the metal arms out of the green pivot support.

1024

Step 2

              Remove the metal melting tray.
  • Remove the 2 screws (.75cm in length) currently securing the metal melting tray with a Phillips #2 screwdriver.

Remove the 2 screws (.75cm in length) currently securing the metal melting tray with a Phillips #2 screwdriver.

Step 3

              Remove the light bulb
  • The light bulb should now be revealed. Unscrew the burned out bulb and replace with a new bulb.

The light bulb should now be revealed. Unscrew the burned out bulb and replace with a new bulb.

Step 4

              Remove the green base from the crayon maker
  • Flip the crayon maker.
  • Remove six screws (2 cm in length) with a spanner.
  • Remove the green base plate and set it aside.

Flip the crayon maker.

Remove six screws (2 cm in length) with a spanner.

Remove the green base plate and set it aside.

Step 5

              Locate the Plastic arm
  • Locate the clear plastic arm inside the control box.

Locate the clear plastic arm inside the control box.

Step 6

              Adjust/Replace the Plastic Arm
  • If necessary, unscrew the plastic arm with a Phillips #00 Precision screwdriver and readjust the arm until the desired position is reached.
  • If the plastic arm is broken, contact Crayola for replacement parts.

If necessary, unscrew the plastic arm with a Phillips #00 Precision screwdriver and readjust the arm until the desired position is reached.

If the plastic arm is broken, contact Crayola for replacement parts.

Step 7

              Locate the clear plastic box
  • Remove the green base from the crayon maker and set aside.
  • Locate the clear box.

Remove the green base from the crayon maker and set aside.

Locate the clear box.

Step 8

              Remove clear box.
  • There are four screws (circled in red) that need to be removed with a Phillips #00 Precision screwdriver.

There are four screws (circled in red) that need to be removed with a Phillips #00 Precision screwdriver.

Step 9

              Open Clear Plastic Box
  • Remove five screws (1.5 cm in length) using a Phillips #00 Precision screwdriver and open the clear plastic box.

Remove five screws (1.5 cm in length) using a Phillips #00 Precision screwdriver and open the clear plastic box.

Step 10

              Check placement of white plastic arm.
  • The plastic arm should be positioned as shown in the figure. Adjust the arm’s position if necessary.
  • If the plastic arm is broken, contact Crayola for a replacement arm.

The plastic arm should be positioned as shown in the figure. Adjust the arm’s position if necessary.

If the plastic arm is broken, contact Crayola for a replacement arm.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 13 other contributors 


                    Melissa

Member since: 10/10/2014

210 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges