Difficulty
Easy
Steps
12
Time Required
2 hours
Sections
1
- Cushion Padding and Upholstery
- 12 steps
Flags
0
BackCosco Stylaire Step Stool (44-B)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Cushion Padding and Upholstery
- Cut two pieces of foam for each seat cushion.
- Bottom seat: 14" x 12"
- Back rest: 14" x 6"
Cut two pieces of foam for each seat cushion.
Bottom seat: 14" x 12"
Back rest: 14" x 6"
1024
Step 2
- Cut two pieces of oil cloth for each seat.
- Bottom seat: 20" x 18"
- Back rest: 17.5" x 9.5"
Cut two pieces of oil cloth for each seat.
Bottom seat: 20" x 18"
Back rest: 17.5" x 9.5"
Step 3
- Using a Phillips #0 screwdriver, unscrew the back rest from the stool.
Using a Phillips #0 screwdriver, unscrew the back rest from the stool.
Step 4
- To detach the seat, lift up the seat and use a flathead screwdriver to lift up all four tabs underneath.
To detach the seat, lift up the seat and use a flathead screwdriver to lift up all four tabs underneath.
Step 5
- Use the flathead screwdriver to pry the top of the seat off.
- The base of the seat will stay attached to the stool.
Use the flathead screwdriver to pry the top of the seat off.
The base of the seat will stay attached to the stool.
Step 6
- Use a flathead screwdriver to lift up the tabs on the back rest to remove the metal plate.
Use a flathead screwdriver to lift up the tabs on the back rest to remove the metal plate.
Step 7
- Remove old materials from each metal seat plate.
- You may need to use a paint scraper to scrape off the foam.
Remove old materials from each metal seat plate.
You may need to use a paint scraper to scrape off the foam.
Step 8
- Clean off any rust using vinegar and paper towels.
Clean off any rust using vinegar and paper towels.
Step 9
- Use the spray adhesive to spray the metal plates and apply the foam to their respective pieces.
- Let it sit for five minutes to dry.
Use the spray adhesive to spray the metal plates and apply the foam to their respective pieces.
Let it sit for five minutes to dry.
Step 10
- Spray adhesive onto foam and center each metal plate on the cloth so that there is an equal amount of cloth peeking out on all four sides.
Spray adhesive onto foam and center each metal plate on the cloth so that there is an equal amount of cloth peeking out on all four sides.
Step 11
- Smooth cloth onto each metal plate, pushing from the center, outwards.
Smooth cloth onto each metal plate, pushing from the center, outwards.
Step 12
- Fold the cloth up over the sides and clothespin it down along all four edges.
- Let it dry for at least one hour.
Fold the cloth up over the sides and clothespin it down along all four edges.
Let it dry for at least one hour.
To reassemble your device, follow steps 3-5 in reverse order, using a hammer to push down the tabs.
Cancel: I did not complete this guide.
6 other people completed this guide.
Author
with 2 other contributors
JacQueline Walker
Member since: 01/30/2018
401 Reputation
1 Guide authored
Badges:
8
+5 more badges
Team
Eastern Washington University, Team S27-G1, Crane Winter 2018
Member of Eastern Washington University, Team S27-G1, Crane Winter 2018
EWU-CRANE-W18S27G1
4 Members
5 Guides authored
gchan - Jul 7, 2021
Reply
Instructions were perfect. Pictures were very helpful, and I was able to successfully (and easily because of the detail provided) finish upholstering my chair. Follow the instructions and you’ll be successful too!
