Difficulty
Very difficult
Steps
9
Time Required
45 minutes
Sections
3
- Earcup
- 3 steps
- Battery
- 3 steps
- Lights
- 3 steps
Flags
0
BackCorsair Void Pro RGB
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Earcup
- Carefully remove earmuff from headphones by getting a grip under the earmuff cushion and peeling up over the lip that keeps it in place.
Carefully remove earmuff from headphones by getting a grip under the earmuff cushion and peeling up over the lip that keeps it in place.
1024
Step 2
- Using the Phillips #0 screwdriver, unscrew the seven 6.4 mm screws holding the black speaker cover in place.
- If you are disassembling the lefthand earfmuff, there will be eight 6.4 mm screws to remove.
Using the Phillips #0 screwdriver, unscrew the seven 6.4 mm screws holding the black speaker cover in place.
If you are disassembling the lefthand earfmuff, there will be eight 6.4 mm screws to remove.
Step 3
- Remove and set aside the black panel, taking care to keep the wires attached.
- The panel should lift up without much force. If the panel does not budge, carefully use the iFixit plastic opening tool to dislodge the piece.
Remove and set aside the black panel, taking care to keep the wires attached.
The panel should lift up without much force. If the panel does not budge, carefully use the iFixit plastic opening tool to dislodge the piece.
Step 4
Battery
- Using the Phillips #0 screwdriver, remove the three 6.4 mm screws on the black plastic panel with the grid of holes.
Using the Phillips #0 screwdriver, remove the three 6.4 mm screws on the black plastic panel with the grid of holes.
Step 5
- Carefully unplug the wire that connects the battery pack to the headphones.
- This should not take too much force.
Carefully unplug the wire that connects the battery pack to the headphones.
This should not take too much force.
Step 6
- Remove the clear plastic covering and set aside.
Remove the clear plastic covering and set aside.
Step 7
Lights
- There is a small circuit board near the bottom of the muff.
- Using a Phillips #0 screwdriver, unscrew the single screw holding the circuit board in place.
There is a small circuit board near the bottom of the muff.
Using a Phillips #0 screwdriver, unscrew the single screw holding the circuit board in place.
Step 8
- Remove the circuit board from its plastic slot.
- If this is the first time the lights have been removed from the headphones, you may need to wiggle the circuit board out of place or use plastic tweezers to loosen it from the manufacturer’s adhesive.
Remove the circuit board from its plastic slot.
If this is the first time the lights have been removed from the headphones, you may need to wiggle the circuit board out of place or use plastic tweezers to loosen it from the manufacturer’s adhesive.
Step 9
- Desolder the three points where the wires connect to the circuit board. For detailed instructions on soldering, see this helpful guide.
- Take note of where each of the wires goes to simplify the resoldering process.
- Follow these steps again to replace the light on the other earcup.
Desolder the three points where the wires connect to the circuit board. For detailed instructions on soldering, see this helpful guide.
Take note of where each of the wires goes to simplify the resoldering process.
Follow these steps again to replace the light on the other earcup.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Gianna Nobili
Member since: 04/15/2019
809 Reputation
5 Guides authored
Badges:
11
+8 more badges
Team
Cal Poly, Team S9-G13, Maness Spring 2019
Member of Cal Poly, Team S9-G13, Maness Spring 2019
CPSU-MANESS-S19S9G13
4 Members
12 Guides authored
