Difficulty

Moderate

Steps

6

Time Required

                          10 minutes

Sections

2

  • Earcup
  • 3 steps
  • Battery
  • 3 steps

Flags

0

  • BackCorsair Void Pro RGB

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Instructions for removing the battery all refer to the right hand earmuff.

What you need

Step 1

              Earcup
  • Carefully remove earmuff from headphones by getting a grip under the earmuff cushion and peeling up over the lip that keeps it in place.

Carefully remove earmuff from headphones by getting a grip under the earmuff cushion and peeling up over the lip that keeps it in place.

1024

Step 2

  • Using the Phillips #0 screwdriver, unscrew the seven 6.4 mm screws holding the black speaker cover in place.
  • If you are disassembling the lefthand earfmuff, there will be eight 6.4 mm screws to remove.

Using the Phillips #0 screwdriver, unscrew the seven 6.4 mm screws holding the black speaker cover in place.

If you are disassembling the lefthand earfmuff, there will be eight 6.4 mm screws to remove.

Step 3

  • Remove and set aside the black panel, taking care to keep the wires attached.
  • The panel should lift up without much force. If the panel does not budge, carefully use the iFixit plastic opening tool to dislodge the piece.

Remove and set aside the black panel, taking care to keep the wires attached.

The panel should lift up without much force. If the panel does not budge, carefully use the iFixit plastic opening tool to dislodge the piece.

Step 4

              Battery
  • Using the Phillips #0 screwdriver, remove the three 6.4 mm screws on the black plastic panel with the grid of holes.

Using the Phillips #0 screwdriver, remove the three 6.4 mm screws on the black plastic panel with the grid of holes.

Step 5

  • Carefully unplug the wire that connects the battery pack to the headphones.
  • This should not take too much force.

Carefully unplug the wire that connects the battery pack to the headphones.

This should not take too much force.

Step 6

  • Remove the clear plastic covering and set aside.

Remove the clear plastic covering and set aside.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      13 other people completed this guide.

Author

                                      with 5 other contributors 


                    Gianna Nobili

Member since: 04/15/2019

809 Reputation

                                      5 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team S9-G13, Maness Spring 2019                        

                                                  Member of Cal Poly, Team S9-G13, Maness Spring 2019 



                    CPSU-MANESS-S19S9G13                     


                                            4 Members                     


                                            12 Guides authored

Vincent Poirier - May 28, 2020

Reply

Someone knows where to find the charging connector for the headset or can it be changed for usb-c?

Cesar Ruiz - Jun 25, 2020

It can be charge with any other USB mini/micro cable like the one for android phones, prior to USB-C

Unless your model of headset only allows USB-C then yes use any USB-C

Cesar Ruiz - Jun 25, 2020

Reply

Can someone please add a link to where you can buy this replacement battery - I would like to order a few.

Justin Bell - Mar 4, 2021

So the battery that I ordered from here is a 700mAh. The on that I ordered from the link here is an 700mAh. Time to send this back and shop again

Jason HKB - Feb 6, 2021

Reply

Can u show how to change “Charging Port”??