Coby Kyros Mid7024 Battery Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Back Cover
3 steps
Battery
3 steps

Flags

BackCoby Kyros MID7024
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Cover

Begin by ensuring that the device is powered off.
To replace the back cover of the device you must pry it open using the access points. One is located on the top of the device above the camera and the other is on the bottom left hand side.
Use the spudger to pry at the access points to open the device.

Begin by ensuring that the device is powered off.

To replace the back cover of the device you must pry it open using the access points. One is located on the top of the device above the camera and the other is on the bottom left hand side.

Use the spudger to pry at the access points to open the device.

1024

Step 2

Once the back cover begins to separate from the body of the device continue working the spudger around the perimeter of the device until the back cover is free.
You will hear some popping and cracking noises as you pry open the device. These sounds are the internal clips coming apart.
Once the back cover is free from the body of the device, open both sides like a book, placing them flat on the table as shown. Be sure to pay attention to the speaker wires that hold the two pieces together.

Once the back cover begins to separate from the body of the device continue working the spudger around the perimeter of the device until the back cover is free.

You will hear some popping and cracking noises as you pry open the device. These sounds are the internal clips coming apart.

Once the back cover is free from the body of the device, open both sides like a book, placing them flat on the table as shown. Be sure to pay attention to the speaker wires that hold the two pieces together.

Step 3

This step is only necessary if you intend to repair or replace the back cover and/or speakers of the device.
In order to replace the back cover you must remove the speakers. Place the Spudger under the plastic frame of the speaker as shown. Pry up, popping the corners of the speakers out of of their bracket and lift the speaker out.
Be sure not to pull on the speaker’s wires or body too hard as you may damage them.

This step is only necessary if you intend to repair or replace the back cover and/or speakers of the device.

In order to replace the back cover you must remove the speakers. Place the Spudger under the plastic frame of the speaker as shown. Pry up, popping the corners of the speakers out of of their bracket and lift the speaker out.

Be sure not to pull on the speaker’s wires or body too hard as you may damage them.

Step 4

              Battery

Locate the black tape connected to the battery and peel it back as indicated in the images.

Locate the black tape connected to the battery and peel it back as indicated in the images.

Step 5

The battery is held to the device with two adhesive strips located on its underside.
After the battery is freed from the device, it will remain connected to the motherboard by two short wires.
Use the spudger tool to gently pry around both sides of the battery until it can be lifted from the device.
Roll the battery over (as shown in the image) so that its underside is now facing up. This will prevent damage to the motherboard.

The battery is held to the device with two adhesive strips located on its underside.

After the battery is freed from the device, it will remain connected to the motherboard by two short wires.

Use the spudger tool to gently pry around both sides of the battery until it can be lifted from the device.

Roll the battery over (as shown in the image) so that its underside is now facing up. This will prevent damage to the motherboard.

Step 6

Use a soldering gun to remove the positive and negative wires connecting the battery to the motherboard.
Follow the guide on soldering to assist you in removing the battery.

Use a soldering gun to remove the positive and negative wires connecting the battery to the motherboard.

Follow the guide on soldering to assist you in removing the battery.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Kyle Williams

Member since: 03/21/2016

246 Reputation

                                      2 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Clemson, Team 6-3, Benson Spring 2016                        

                                                  Member of Clemson, Team 6-3, Benson Spring 2016 



                    CLEM-BENSON-S16S6G3                     


                                            4 Members                     


                                            16 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team