Cleaning The Ulco Integrus Psv Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Cleaning the Ulco Integrus PSV
8 steps

Flags

BackUlco Integrus PSV
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

To begin, make sure the ventilator is turned off and unplugged.

These should be cleaned each day that the ventilator is in use (usually at the end of the day).

NOTE: Screw types and lengths are not specified in manuals

Step 1

              Cleaning the Ulco Integrus PSV

Absorber
Loosen the knurled screws and remove the clear lid.

Absorber

Loosen the knurled screws and remove the clear lid.

1024

Step 2

Remove the silicone shutters by gently lifting from the base, NOT from the flaps.

Remove the silicone shutters by gently lifting from the base, NOT from the flaps.

Step 3

To release and remove the canister(s), undo the handle latch by turning sideways.

To release and remove the canister(s), undo the handle latch by turning sideways.

Step 4

Push the release handle down to vertical until canisters are free.

Push the release handle down to vertical until canisters are free.

Step 5

Push canister(s) down then out of the cradle. Then dispose of the used soda lime (see suppliers recommended procedure for disposal of soda lime).
Wash all the absorber components. Do NOT use caustic cleaning fluids.
The Canister(s) and silicone shutters can be autoclaved.
The Absorber head can be put through a washer at 80 deg.C
Dry thoroughly before assembly, low pressure warm air should be passed through the head by attaching a hose to the expiratory port of the absorber.

Push canister(s) down then out of the cradle. Then dispose of the used soda lime (see suppliers recommended procedure for disposal of soda lime).

Wash all the absorber components. Do NOT use caustic cleaning fluids.

The Canister(s) and silicone shutters can be autoclaved.

The Absorber head can be put through a washer at 80 deg.C

Dry thoroughly before assembly, low pressure warm air should be passed through the head by attaching a hose to the expiratory port of the absorber.

Step 6

Bellows Assembly
Loosen the four knurled screws (1) and remove the bellows canister.

Bellows Assembly

Loosen the four knurled screws (1) and remove the bellows canister.

Step 7

Remove the bellows assembly by rotating counter-clockwise. The bellows canister may be washed or autoclaved.

Remove the bellows assembly by rotating counter-clockwise. The bellows canister may be washed or autoclaved.

Step 8

The base disk (mushroom) should be removed from the bellows assembly before washing. Pull the latex-free rubber bag from the delrin base disk. The bellows may be washed or autoclaved. The base component (mushroom) should not be autoclaved but can be put through a washer at 80°C.
Dry all components thoroughly before re-assembly.
Low pressure warm air should be passed through the absorber head by attaching a hose to the scavenge port

The base disk (mushroom) should be removed from the bellows assembly before washing. Pull the latex-free rubber bag from the delrin base disk. The bellows may be washed or autoclaved. The base component (mushroom) should not be autoclaved but can be put through a washer at 80°C.

Dry all components thoroughly before re-assembly.

Low pressure warm air should be passed through the absorber head by attaching a hose to the scavenge port

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Jacob Henriksen

Member since: 04/15/2019

232 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team S7-G13, Paton Spring 2020                        

                                                  Member of Cal Poly, Team S7-G13, Paton Spring 2020 



                    CPSU-PATON-S20S7G13                     


                                            3 Members                     


                                            8 Guides authored

Introduction#

Team#

Introduction

Team