Difficulty
Moderate
Steps
11
Time Required
10 - 20 minutes
Sections
4
- Power Cable Disconnect
- 1 step
- Dust Bag
- 1 step
- Dust Tube
- 1 step
- Fan Belt
- 8 steps
Flags
1
In Progress
This guide is a work in progress. Reload periodically to see the latest changes!
BackAmerican Sanders EZ-8 Floor Sander 07012A (2012)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Disconnect all power cables
- Before you begin your repair, disconnect all power cables to reduce the risk of short circuits and electric shock.
Before you begin your repair, disconnect all power cables to reduce the risk of short circuits and electric shock.
1024
Step 2
Remove the dust bag
- Pull on the dust bag to remove it from the dust tube.
- If the dust bag doesn’t slide off easily, gently twist it back and forth while pulling to free it from the tube.
Pull on the dust bag to remove it from the dust tube.
If the dust bag doesn’t slide off easily, gently twist it back and forth while pulling to free it from the tube.
Step 3
Remove the dust tube
- Pull up on the dust tube to remove it from the sander.
Pull up on the dust tube to remove it from the sander.
Step 4
Remove the belt guard screws
- Use a long Phillips #2 screwdriver to remove the two screws securing the belt guard:
- One 1/4-20 x 18 mm screw
- One 1/4-20 x 30 mm screw
Use a long Phillips #2 screwdriver to remove the two screws securing the belt guard:
One 1/4-20 x 18 mm screw
One 1/4-20 x 30 mm screw
Step 5
Remove the belt guard
- Remove the belt guard.
Remove the belt guard.
Step 6
Remove the dust shoe plate
- Carefully tilt the floor sander onto its side, exposing the sanding drum and the dust shoe plate.
- Use a Phillips #2 screwdriver to remove the four screws on the underside of the sander securing the dust shoe plate.
- Remove the dust shoe plate.
Carefully tilt the floor sander onto its side, exposing the sanding drum and the dust shoe plate.
Use a Phillips #2 screwdriver to remove the four screws on the underside of the sander securing the dust shoe plate.
Remove the dust shoe plate.
Step 7
Loosen the motor mount nuts
- In the following steps you will loosen the nuts that hold the motor in place on the frame of the sander to release the tension on the fan belt.
- For the purposes of this repair, there is no need to fully remove any of the nuts in the following steps. Just loosen them enough to allow the motor to slide back and forth.
In the following steps you will loosen the nuts that hold the motor in place on the frame of the sander to release the tension on the fan belt.
For the purposes of this repair, there is no need to fully remove any of the nuts in the following steps. Just loosen them enough to allow the motor to slide back and forth.
Step 8
- Use a socket wrench with an extension and a deep 1/2" socket to loosen the two nuts behind the dust shoe plate.
- The nuts may be very tight. Use a breaker bar or impact driver if necessary.
Use a socket wrench with an extension and a deep 1/2" socket to loosen the two nuts behind the dust shoe plate.
The nuts may be very tight. Use a breaker bar or impact driver if necessary.
Step 9
- Use a 1/2" wrench to loosen the other two nuts securing the motor.
Use a 1/2" wrench to loosen the other two nuts securing the motor.
Step 10
De-tension the fan belt
- Slide the motor along its mounting slots toward the back of the sander until the fan belt is detensioned.
- During reassembly, slide the motor back to its original position before tightening the four motor mount nuts. Check that both belts are properly tracked and tensioned before securing the belt guard back into place.
Slide the motor along its mounting slots toward the back of the sander until the fan belt is detensioned.
During reassembly, slide the motor back to its original position before tightening the four motor mount nuts. Check that both belts are properly tracked and tensioned before securing the belt guard back into place.
Step 11
Remove the fan belt
- Remove the fan belt.
Remove the fan belt.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 2 other contributors
Taylor Dixon
Member since: 06/26/2018
62,097 Reputation
94 Guides authored
Badges:
40
+37 more badges
Team
Teardown Team
Member of Teardown Team
Community
2 Members
2,047 Guides authored
SARAH - Jul 24, 2020
Reply
i would have never thought to lower the motor, i would love a video but this demo helped me get my belt replaced without the hassle of wondering how to stretch the belt!
