Cisco 878 Router Strataflash Memory Module Replacement Upgrade Repair Guide

Difficulty

Moderate

Steps

6

Time Required

                          30 minutes            

Sections

4

• Cisco 878 Integrated Services Router Top Cover Disassembly
• 2 steps
• Cisco 878 Integrated Services Router Inner Metal Shield Disassembly
• 2 steps
• Cisco 878 Integrated Services Router StrataFlash Memory module Disassembly
• 1 step
• Cisco 878 Router StrataFlash Memory module
• 1 step

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackCisco 878 Integrated Services Router

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Remove the two screws on back side               

• Only trained and qualified personnel should be allowed to install, replace, or service this equipment!
• During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself!
• Make sure that the power switch is turned to standby and that the power supply cable is disconnected. Disconnect all cables from the router back panel.
• Use the Phillips #1 Screwdriver to remove the two screws on back side of the device.

Only trained and qualified personnel should be allowed to install, replace, or service this equipment!

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself!

Make sure that the power switch is turned to standby and that the power supply cable is disconnected. Disconnect all cables from the router back panel.

Use the Phillips #1 Screwdriver to remove the two screws on back side of the device.

1024

Step 2

              Remove top cover               

• 1. Gently push the top cover of the router away from you.
• 2. Lift it up top cover from the bottom of the router.
• 3. Remove top cover from the device.
• Place the router bottom on an antistatic mat.

1. Gently push the top cover of the router away from you.

2. Lift it up top cover from the bottom of the router.

3. Remove top cover from the device.

Place the router bottom on an antistatic mat.

Step 3

              Remove the three screws on front side               

• Use the Phillips #1 Screwdriver to remove the three screws on front side of the device.

Use the Phillips #1 Screwdriver to remove the three screws on front side of the device.

Step 4

              Remove the inner metal shield               

• 1. Gently lift up inner metal shield from the bottom of the router.
• 2. Remove inner metal shield from the device (see the anchors on the picture).
• Be careful and do not distort the plates!

1. Gently lift up inner metal shield from the bottom of the router.

2. Remove inner metal shield from the device (see the anchors on the picture).

Be careful and do not distort the plates!

Step 5

              Remove  StrataFlash Memory module               

• 1. Place your fingers on the levers at the two sides of the slot, and push open.
• 2. Firmly pull the release lever away from the module until the module pops up.
• 3. You can then remove the module from the module slot.

1. Place your fingers on the levers at the two sides of the slot, and push open.

2. Firmly pull the release lever away from the module until the module pops up.

3. You can then remove the module from the module slot.

Step 6

              Installing new module               

• 1. Insert the notched edge of the module into the slot at an angle.
• 2. Firmly press down the unnotched edge of the module until you hear a click. The indents must be fully in the notches.

1. Insert the notched edge of the module into the slot at an angle.

2. Firmly press down the unnotched edge of the module until you hear a click. The indents must be fully in the notches.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Attached Documents

• Upgrading-Memory-in-Cisco-878.pdf
• PDF - 359.66 kb
• View

Upgrading-Memory-in-Cisco-878.pdf

PDF - 359.66 kb

Author

                                      with 1 other contributor 

                    Jiri Altman                     

Member since: 05/03/2016

1,479 Reputation

                                      8 Guides authored                  



                       Badges:
                       21





                                                        +18 more badges                           

Team

                       4k20 Repair Team                        

                                                  Member of 4k20 Repair Team 



                    Community                     


                                            2 Members                     


                                            16 Guides authored