Difficulty
Difficult
Steps
8
Time Required
15 - 20 minutes
Sections
2
- Case
- 4 steps
- Sharpening Stones
- 4 steps
Flags
0
BackChef’s Choice M115
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Case
- Remove the two rubber feet on the motor side of the device.
- Remove the five Phillips screws from the bottom of the case.
- These screws are recessed deep in the device, so a long, thin screwdriver is required.
Remove the two rubber feet on the motor side of the device.
Remove the five Phillips screws from the bottom of the case.
These screws are recessed deep in the device, so a long, thin screwdriver is required.
1024
Step 2
- Remove the two hex-cap screws on the bottom using a pair of pliers.
Remove the two hex-cap screws on the bottom using a pair of pliers.
Step 3
- Carefully flip the device right-side-up while grasping the top and bottom pieces.
- The white cover should lift off with no resistance. If it does not, ensure all screws were removed in previous step.
Carefully flip the device right-side-up while grasping the top and bottom pieces.
The white cover should lift off with no resistance. If it does not, ensure all screws were removed in previous step.
Step 4
- Remove the sharpener guard by gently pulling up on it.
- If the sharpener guard does not come off easily, ensure all screws were removed in step 1.
Remove the sharpener guard by gently pulling up on it.
If the sharpener guard does not come off easily, ensure all screws were removed in step 1.
Step 5
Sharpening Stones
- With the outer case removed, firmly grasp the motor-axle attachment and remove it from the base. It should come right off of the assembly.
With the outer case removed, firmly grasp the motor-axle attachment and remove it from the base. It should come right off of the assembly.
Step 6
- Use a screwdriver to push the linkage pins out of the rod.
- Use pliers to pull the pins the rest of the way out.
- Remove all the linkage pins necessary to slide desired sharpening stone off the end of the shaft.
Use a screwdriver to push the linkage pins out of the rod.
Use pliers to pull the pins the rest of the way out.
Remove all the linkage pins necessary to slide desired sharpening stone off the end of the shaft.
Step 7
- On the rotating apparatus, holding the sharpening stones in place, are two C-clamps that grip the axle.
- Remove the C-clamps by applying pressure to both sides of the “C” and pushing the clamp over and off of the axle.
- Pull the bearing off the shaft. It is in between the two C-clamps.
- These clamps are very small; use caution to avoid dropping them on the ground or losing them.
On the rotating apparatus, holding the sharpening stones in place, are two C-clamps that grip the axle.
Remove the C-clamps by applying pressure to both sides of the “C” and pushing the clamp over and off of the axle.
Pull the bearing off the shaft. It is in between the two C-clamps.
These clamps are very small; use caution to avoid dropping them on the ground or losing them.
Step 8
- Pull sharpening stones off the end of the shaft.
- Be sure to remember the order and placement of each individual stone so you can reassemble them in the same order.
Pull sharpening stones off the end of the shaft.
Be sure to remember the order and placement of each individual stone so you can reassemble them in the same order.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 5 other contributors
Zachary Nagel
Member since: 09/17/2015
116 Reputation
1 Guide authored
Badges:
8
+5 more badges
Team
IUPUI, Team 3-3, Harley Fall 2015
Member of IUPUI, Team 3-3, Harley Fall 2015
IUPUI-HARLEY-F15S3G3
5 Members
12 Guides authored
john molloy - Jun 19, 2021
Reply
where does one get the replacement stones. im not seeing they in my amazon/google searches. also cant seem to see them on manufacturers website section for parts.
