Changing The Bath Nf Siryo Chrome Thermostatic Cartridge Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

SIRYO CHROME thermostatic cartridge
6 steps

Flags

BackThermostatic faucet
Full Screen
Options
History
Save to Favorites
Download PDF
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Step 1

              Access to the thermostatic cartridge

WARNING: Before any intervention, make sure that the inverter is in the “OFF” position and close the water supply to the meter.
Using a flat screwdriver, unclip the cover to access the handle fixing screw.
Unscrew the fixing screw counterclockwise.

WARNING: Before any intervention, make sure that the inverter is in the “OFF” position and close the water supply to the meter.

Using a flat screwdriver, unclip the cover to access the handle fixing screw.

Unscrew the fixing screw counterclockwise.

1024

Step 2

              Dismantling the thermostatic handle

Before disassembling, check that the mark on the mixer tap is aligned with the “38°” position, then remove the handle.
ATTENTION: before extracting the stop ring (38°), check that the two notches are aligned with the mark on the mixer
Extract the thrust ring

Before disassembling, check that the mark on the mixer tap is aligned with the “38°” position, then remove the handle.

ATTENTION: before extracting the stop ring (38°), check that the two notches are aligned with the mark on the mixer

Extract the thrust ring

Step 3

              Removing the thermostatic cartridge

Unscrew the thermostatic cartridge anti-clockwise using a 21 wrench.
Extract the cartridge by hand.

Unscrew the thermostatic cartridge anti-clockwise using a 21 wrench.

Extract the cartridge by hand.

Step 4

              Reassembly

Insert the thermostat in the mixer body.
Screw in clockwise by hand.
Finish the tightening using the spanner 21.
ATTENTION: The tightening torque must not exceed 10Nm. We therefore advise you to use a torque wrench so as not to damage the thread of the thermostatic cartridge.

Insert the thermostat in the mixer body.

Screw in clockwise by hand.

Finish the tightening using the spanner 21.

ATTENTION: The tightening torque must not exceed 10Nm. We therefore advise you to use a torque wrench so as not to damage the thread of the thermostatic cartridge.

Step 5

              Replacing and adjusting the stop ring

Position the two lines marked on the stop ring facing the point of the mixer tap.
Turn on the water supply to proceed with the adjustment step.
Turn the diverter handle to run the water, then place a thermometer under the flow to check the correct temperature, which should be 38°.
If the temperature is not 38°, adjust by turning the wheel clockwise to decrease the temperature (-°C).
And counterclockwise to increase the temperature (+°C).

Position the two lines marked on the stop ring facing the point of the mixer tap.

Turn on the water supply to proceed with the adjustment step.

Turn the diverter handle to run the water, then place a thermometer under the flow to check the correct temperature, which should be 38°.

If the temperature is not 38°, adjust by turning the wheel clockwise to decrease the temperature (-°C).

And counterclockwise to increase the temperature (+°C).

Step 6

              Replacing the handle

Align the reference point on the mixer body with the 38° mark on the handle.
Tighten the handle fixing screw using a Phillips screwdriver in a clockwise direction.
Replace the cover.

Align the reference point on the mixer body with the 38° mark on the handle.

Tighten the handle fixing screw using a Phillips screwdriver in a clockwise direction.

Replace the cover.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

HelloMacOS

Annika Faelker

Tay

Author

                                      with 1 other contributor

                    iRobot

Member since: 09/24/2009

1 Reputation

                                      646 Guides authored                  



                       Badges:
                       36







                                                        +33 more badges

Introduction#

Introduction