Difficulty
Difficult
Steps
13
Time Required
15 - 20 minutes
Sections
4
- Exterior Frame and Matting
- 4 steps
- Internal Plastic Screen Frame
- 2 steps
- Display
- 5 steps
- Power Supply Board
- 2 steps
Flags
0
BackCeiva Digital Photo Receiver LF2003
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Exterior Frame and Matting
- Lay the device on its back, and rotate so the base is facing away from you.
Lay the device on its back, and rotate so the base is facing away from you.
1024
Step 2
- Grip the frame with your fingers under the edge of the frame, and thumbs pushing down on the front of the device.
Grip the frame with your fingers under the edge of the frame, and thumbs pushing down on the front of the device.
Step 3
- Lift up the frame with your fingers and push down the rest of the device with your thumbs.
Lift up the frame with your fingers and push down the rest of the device with your thumbs.
Step 4
- Remove the frame and matte from the device.
Remove the frame and matte from the device.
Step 5
Internal Plastic Screen Frame
- Remove the four 7mm Torx T6 screws.
Remove the four 7mm Torx T6 screws.
Step 6
- Using the plastic opening tool or your fingers, lift up the frame from any edge.
- Remove the frame from the device.
Using the plastic opening tool or your fingers, lift up the frame from any edge.
Remove the frame from the device.
Step 7
Display
- Unplug the cable connecting the display to the power supply using the flat end of the spudger to pry the connector away from the circuit board.
- Alternate applying pressure to the left and right side of the connector to ensure that it does not break.
Unplug the cable connecting the display to the power supply using the flat end of the spudger to pry the connector away from the circuit board.
Alternate applying pressure to the left and right side of the connector to ensure that it does not break.
Step 8
Step 9
- Lift up the display from the left edge and flip display over.
- Do not lift the display too quickly, as the display is still connected to the main circuit board on the right.
Lift up the display from the left edge and flip display over.
Do not lift the display too quickly, as the display is still connected to the main circuit board on the right.
Step 10
- Use the spudger to disconnect the ribbon cable from the display by the black pins away from the connector. There is a pin on either side of the connector.
- Once both pins are released, the ribbon cable should slide easily out.
- It may be easier if someone else holds the display so the cable does not get ripped out.
Use the spudger to disconnect the ribbon cable from the display by the black pins away from the connector. There is a pin on either side of the connector.
Once both pins are released, the ribbon cable should slide easily out.
It may be easier if someone else holds the display so the cable does not get ripped out.
Step 11
- Remove the display assembly from the device.
Remove the display assembly from the device.
Step 12
Power Supply Board
Step 13
- Desolder the 3 wires attached to the board.
- Remove the power supply board from the device.
- The wires shown were not actually desoldered, but the board will now be separated from the rest of the device.
Desolder the 3 wires attached to the board.
Remove the power supply board from the device.
The wires shown were not actually desoldered, but the board will now be separated from the rest of the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Casey Glasgow
Member since: 01/26/2014
510 Reputation
5 Guides authored
Badges:
7
+4 more badges
Team
Cal Poly, Team 9-25, Maness Winter 2014
Member of Cal Poly, Team 9-25, Maness Winter 2014
CPSU-MANESS-W14S9G25
4 Members
5 Guides authored
