Difficulty
Moderate
Steps
15
Time Required
10 - 15 minutes
Sections
1
- Casio Exilim EX-Z850 Battery Casing Disassembly
- 15 steps
Flags
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackCasio Exilim EX-Z850
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Casio Exilim EX-Z850 Battery Casing Disassembly
- Remove battery before you begin disassembly.
- Use a Phillips #00 Screwdriver to remove all four of the screws on the right side of the camera with the lens facing you.
Remove battery before you begin disassembly.
Use a Phillips #00 Screwdriver to remove all four of the screws on the right side of the camera with the lens facing you.
1024
Step 2
- Use a Phillips #00 screwdriver, unscrew all four screws on the left side of the camera.
Use a Phillips #00 screwdriver, unscrew all four screws on the left side of the camera.
Step 3
- Use the Phillips #00 screwdriver to remove all four of the screws on the bottom of the camera.
- Bottom screws are longer than the top screws, so label accordingly for easy reassembly.
Use the Phillips #00 screwdriver to remove all four of the screws on the bottom of the camera.
Bottom screws are longer than the top screws, so label accordingly for easy reassembly.
Step 4
- Once all screws have been removed, slowly pry open the back casing of the camera.
- Gently remove the ribbon cable from the LCD with tweezers.
- Set aside back casing of the camera.
Once all screws have been removed, slowly pry open the back casing of the camera.
Gently remove the ribbon cable from the LCD with tweezers.
Set aside back casing of the camera.
Step 5
- Use your tweezers to hold the camera secure, while you pull the front cover off of the camera.
Use your tweezers to hold the camera secure, while you pull the front cover off of the camera.
Step 6
- The bottom of the LCD screen is secured to the frame by small pieces of black tape. You will need to peel the tape away to release the LCD screen.
- Use your tweezers to lift the LCD screen from the frame.
The bottom of the LCD screen is secured to the frame by small pieces of black tape. You will need to peel the tape away to release the LCD screen.
Use your tweezers to lift the LCD screen from the frame.
Step 7
- Lift screen away from the camera with your tweezers.
- Flip screen over gently with your fingers once it is lifted far away enough from the camera.
Lift screen away from the camera with your tweezers.
Flip screen over gently with your fingers once it is lifted far away enough from the camera.
Step 8
- Use your tweezers to lift the LCD frame from the camera.
Use your tweezers to lift the LCD frame from the camera.
Step 9
- Use your tweezers to lift the bar holding the ribbon off.
- Disconnect the ribbon to release the LCD screen.
- Use your fingers to pull the LCD screen with the attached ribbon from the camera.
Use your tweezers to lift the bar holding the ribbon off.
Disconnect the ribbon to release the LCD screen.
Use your fingers to pull the LCD screen with the attached ribbon from the camera.
Step 10
- Use a Phillips #00 screwdriver to remove the two screws from the side of the camera that has the strap mount.
- Remove strap mount by slowly pulling the side of the case so it will dislocate from the top of the camera.
Use a Phillips #00 screwdriver to remove the two screws from the side of the camera that has the strap mount.
Remove strap mount by slowly pulling the side of the case so it will dislocate from the top of the camera.
Step 11
- Hold the camera facing toward you. Pull up the bar that is securing the ribbon located to the left of the flash.
- Disconnect the ribbon by prying it off with your fingers.
Hold the camera facing toward you. Pull up the bar that is securing the ribbon located to the left of the flash.
Disconnect the ribbon by prying it off with your fingers.
Step 12
- With the lens facing towards you, pull the L-shaped frame away from the camera.
- Do not disconnect any of the wires from the camera when pulling the frame.
- Remove the frame from the two studs and metal tabs keeping it in place at the bottom of the camera.
With the lens facing towards you, pull the L-shaped frame away from the camera.
Do not disconnect any of the wires from the camera when pulling the frame.
Remove the frame from the two studs and metal tabs keeping it in place at the bottom of the camera.
Step 13
- Locate the logic board to the left of the lens. You will see a bar securing a ribbon. Flip the bar up to release the ribbon.
- Disconnect the ribbon.
Locate the logic board to the left of the lens. You will see a bar securing a ribbon. Flip the bar up to release the ribbon.
Disconnect the ribbon.
Step 14
- Use your Phillips #00 screwdriver to remove the two screws connecting the frame to the back of the camera.
- Lift the frame away on the LCD screen side of the camera.
Use your Phillips #00 screwdriver to remove the two screws connecting the frame to the back of the camera.
Lift the frame away on the LCD screen side of the camera.
Step 15
- This is what your camera should look like now that you have the battery casing isolated.
This is what your camera should look like now that you have the battery casing isolated.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 13 other contributors
Logan
Member since: 01/10/2011
311 Reputation
2 Guides authored
Badges:
4
+1 more badge
Team
Cal Poly, Team 4-38, Regan Winter 2011
Member of Cal Poly, Team 4-38, Regan Winter 2011
CPSU-REGAN-W11S4G38
4 Members
13 Guides authored
