Casio Exilim Ex Z80 Lcd Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          55 seconds - 4 minutes

Sections

Back and Front Cover
7 steps
LCD Screen
3 steps

Flags

BackCasio Exilim EX-Z80
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back and Front Cover

Remove the four 3 mm black screws from the bottom of the camera using a Phillips #000 screwdriver.
Open the battery compartment with your thumb or index finger.
Remove the single 2 mm silver screw that is now exposed using a Phillips #000 screwdriver.

Remove the four 3 mm black screws from the bottom of the camera using a Phillips #000 screwdriver.

Open the battery compartment with your thumb or index finger.

Remove the single 2 mm silver screw that is now exposed using a Phillips #000 screwdriver.

1024

Step 2

Open the USB port tab.
Remove the single 2 mm silver screw using a Phillips #000 screwdriver.

Open the USB port tab.

Remove the single 2 mm silver screw using a Phillips #000 screwdriver.

Step 3

Remove the two 2 mm silver screws using a Phillips #000 screwdriver.

Remove the two 2 mm silver screws using a Phillips #000 screwdriver.

Step 4

Carefully remove the silver strip from left side. Open the battery cover and remove the metal strip with fingers by sliding it to the left.

Carefully remove the silver strip from left side. Open the battery cover and remove the metal strip with fingers by sliding it to the left.

Step 5

With the metal spudger, pry out the edge of the silver strip at the bottom right side of the camera.
Carefully remove the remaining part of the metal strip.

With the metal spudger, pry out the edge of the silver strip at the bottom right side of the camera.

Carefully remove the remaining part of the metal strip.

Step 6

Remove the two 2 mm silver screws from the top corners of the camera using a Phillips #000 screwdriver.
Remove the three 2 mm screws from the left side using a Phillips #000 screwdriver.

Remove the two 2 mm silver screws from the top corners of the camera using a Phillips #000 screwdriver.

Remove the three 2 mm screws from the left side using a Phillips #000 screwdriver.

Step 7

Using a small opening tool carefully release all lock tabs at the top and on the side of the camera from their locked position.
Using your hands, carefully separate the front and back panel from the camera.

Using a small opening tool carefully release all lock tabs at the top and on the side of the camera from their locked position.

Using your hands, carefully separate the front and back panel from the camera.

Step 8

              LCD Screen

Gently flip the wide button cable up from the display cable.
Lift the brown retention flap on the display cable ZIF connector with tweezers or an ESD-safe tool.
Carefully pull the display cable from its connector.

Gently flip the wide button cable up from the display cable.

Lift the brown retention flap on the display cable ZIF connector with tweezers or an ESD-safe tool.

Carefully pull the display cable from its connector.

Step 9

Pry the square holes that hold the LCD screen up with a metal spudger until you see the raised tabs in the metal holes.
Repeat the process with the holes around the four edges of the camera.
Insert the metal spudger into the gap of the metal case and pry up the LCD screen.

Pry the square holes that hold the LCD screen up with a metal spudger until you see the raised tabs in the metal holes.

Repeat the process with the holes around the four edges of the camera.

Insert the metal spudger into the gap of the metal case and pry up the LCD screen.

Step 10

Hold up the LCD screen in one hand and hold back the button cable with the other.
Don’t let the LCD screen to fall back into the metal case and make sure the button cable does not get stuck on the display cable.
Pull on the LCD screen until the yellow display cable is fully out of the metal case.

Hold up the LCD screen in one hand and hold back the button cable with the other.

Don’t let the LCD screen to fall back into the metal case and make sure the button cable does not get stuck on the display cable.

Pull on the LCD screen until the yellow display cable is fully out of the metal case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 6 other contributors

                    Zhiliang Peng

Member since: 04/11/2017

203 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Eastern Washington University, Team S1-G5, Crane Spring 2017                        

                                                  Member of Eastern Washington University, Team S1-G5, Crane Spring 2017 



                    EWU-CRANE-S17S1G5                     


                                            3 Members                     


                                            10 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team