Difficulty
Moderate
Steps
9
Time Required
3 - 10 minutes
Sections
2
- Battery
- 2 steps
- Back and Front Cover
- 7 steps
Flags
0
BackCasio Exilim EX-Z80
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Locate the battery compartment at the bottom of the camera.
- With your thumb, gently press down on the compartment door and slide to the left to open.
Locate the battery compartment at the bottom of the camera.
With your thumb, gently press down on the compartment door and slide to the left to open.
1024
Step 2
- With your index finger, gently pull back gray release lever for the battery to pop out.
- Gently pull the battery out of the slot.
With your index finger, gently pull back gray release lever for the battery to pop out.
Gently pull the battery out of the slot.
Step 3
Back and Front Cover
- Remove the four 3 mm black screws from the bottom of the camera using a Phillips #000 screwdriver.
- Open the battery compartment with your thumb or index finger.
- Remove the single 2 mm silver screw that is now exposed using a Phillips #000 screwdriver.
Remove the four 3 mm black screws from the bottom of the camera using a Phillips #000 screwdriver.
Open the battery compartment with your thumb or index finger.
Remove the single 2 mm silver screw that is now exposed using a Phillips #000 screwdriver.
Step 4
- Open the USB port tab.
- Remove the single 2 mm silver screw using a Phillips #000 screwdriver.
Open the USB port tab.
Remove the single 2 mm silver screw using a Phillips #000 screwdriver.
Step 5
- Remove the two 2 mm silver screws using a Phillips #000 screwdriver.
Remove the two 2 mm silver screws using a Phillips #000 screwdriver.
Step 6
- Carefully remove the silver strip from left side. Open the battery cover and remove the metal strip with fingers by sliding it to the left.
Carefully remove the silver strip from left side. Open the battery cover and remove the metal strip with fingers by sliding it to the left.
Step 7
- With the metal spudger, pry out the edge of the silver strip at the bottom right side of the camera.
- Carefully remove the remaining part of the metal strip.
With the metal spudger, pry out the edge of the silver strip at the bottom right side of the camera.
Carefully remove the remaining part of the metal strip.
Step 8
- Remove the two 2 mm silver screws from the top corners of the camera using a Phillips #000 screwdriver.
- Remove the three 2 mm screws from the left side using a Phillips #000 screwdriver.
Remove the two 2 mm silver screws from the top corners of the camera using a Phillips #000 screwdriver.
Remove the three 2 mm screws from the left side using a Phillips #000 screwdriver.
Step 9
- Using a small opening tool carefully release all lock tabs at the top and on the side of the camera from their locked position.
- Using your hands, carefully separate the front and back panel from the camera.
Using a small opening tool carefully release all lock tabs at the top and on the side of the camera from their locked position.
Using your hands, carefully separate the front and back panel from the camera.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Caroline Villasenor
Member since: 04/11/2017
307 Reputation
3 Guides authored
Badges:
8
+5 more badges
Team
Eastern Washington University, Team S1-G5, Crane Spring 2017
Member of Eastern Washington University, Team S1-G5, Crane Spring 2017
EWU-CRANE-S17S1G5
3 Members
10 Guides authored
