Difficulty
Easy
Steps
8
Time Required
5 - 10 minutes
Sections
1
- Camera Casing
- 8 steps
Flags
0
BackCasio Exilim EX-Z70
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Camera Casing
- Remove the strap from the camera by pulling the thin cord out, creating a small loop, then pushing the thicker cord back through this loop.
Remove the strap from the camera by pulling the thin cord out, creating a small loop, then pushing the thicker cord back through this loop.
1024
Step 2
- Remove the two Phillips screws (2.83 mm) from the left side panel of the camera casing.
- The left panel can now be removed. However, one piece of tape attaches it to the camera, so a spudger may be required to ease the panels off.
- Repeat for the right side panel of the camera.
- Keep track of which screws go where. There are a couple sets of screws to take out and they are all small and look the same.
Remove the two Phillips screws (2.83 mm) from the left side panel of the camera casing.
The left panel can now be removed. However, one piece of tape attaches it to the camera, so a spudger may be required to ease the panels off.
Repeat for the right side panel of the camera.
Keep track of which screws go where. There are a couple sets of screws to take out and they are all small and look the same.
Step 3
- Remove the six Phillips screws (3.69 mm) from the bottom of the camera casing.
Remove the six Phillips screws (3.69 mm) from the bottom of the camera casing.
Step 4
- Remove the two Phillips screws (2.79 mm) on the left side of the camera where the metal panel used to be.
- Repeat for the two Phillips screws (2.79 mm) right side of the camera.
Remove the two Phillips screws (2.79 mm) on the left side of the camera where the metal panel used to be.
Repeat for the two Phillips screws (2.79 mm) right side of the camera.
Step 5
- With the LCD screen facing up towards you, start at the bottom of the camera and gently pull off the back of the casing.
With the LCD screen facing up towards you, start at the bottom of the camera and gently pull off the back of the casing.
Step 6
- With the front side (with the lens) facing up towards you, start at the bottom of the camera and gently pull off the front of the casing.
- The nob that previously held the camera strap will no longer be attached to the camera once you remove the camera casing. When putting the camera back together, remember to put the nob back into position before replacing the casing.
With the front side (with the lens) facing up towards you, start at the bottom of the camera and gently pull off the front of the casing.
The nob that previously held the camera strap will no longer be attached to the camera once you remove the camera casing. When putting the camera back together, remember to put the nob back into position before replacing the casing.
Step 7
- Slide the labeled piece toward the LCD screen and release.
- The tab will spring open.
Slide the labeled piece toward the LCD screen and release.
The tab will spring open.
Step 8
- Look at the bottom of the camera. Take out the Phillips screw (1.77 mm) holding on the bottom plastic piece.
- The bottom plastic piece is held on to the main frame of the camera only by two thin wires.
Look at the bottom of the camera. Take out the Phillips screw (1.77 mm) holding on the bottom plastic piece.
The bottom plastic piece is held on to the main frame of the camera only by two thin wires.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 5 other contributors
Paul Fallon
Member since: 04/10/2012
135 Reputation
6 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 17-28, Amido Spring 2012
Member of Cal Poly, Team 17-28, Amido Spring 2012
CPSU-AMIDO-S12S17G28
4 Members
14 Guides authored
