Casio Cdp 230R Pitch Bend Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          25 - 30 minutes

Sections

Panels
8 steps
Pitch Bend
3 steps

Flags

BackCASIO CDP-230R
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Panels

Flip the keyboard upside down, with the keys on a flat surface.
Remove the three black 14mm Japanese Industrial Standard (J) head screws using a J1 screwdriver on the top half of the outermost side panel.

Flip the keyboard upside down, with the keys on a flat surface.

Remove the three black 14mm Japanese Industrial Standard (J) head screws using a J1 screwdriver on the top half of the outermost side panel.

1024

Step 2

Use two hands to grab the side panel from both sides.
Pull the panel apart from the device one side at a time.
There will be popping sounds when you remove this panel.
One side panel will not have an orange & white cable connected to it.

Use two hands to grab the side panel from both sides.

Pull the panel apart from the device one side at a time.

There will be popping sounds when you remove this panel.

One side panel will not have an orange & white cable connected to it.

Step 3

Remove the three silver 10mm screws with a J1 screwdriver on the bottom half of the innermost side panel of the device.
One side panel will not have an orange & white cable running through.

Remove the three silver 10mm screws with a J1 screwdriver on the bottom half of the innermost side panel of the device.

One side panel will not have an orange & white cable running through.

Step 4

Remove the innermost side panel by pinching the top and bottom of the panel and pulling the panel off with both hands.
There will be popping sounds when you remove this panel.
Repeat steps one through four to remove the other side panel of the keyboard.

Remove the innermost side panel by pinching the top and bottom of the panel and pulling the panel off with both hands.

Repeat steps one through four to remove the other side panel of the keyboard.

Step 5

Remove the two black 30 mm J head screws with a J1 screwdriver to remove the long black bar.
Remove the four silver 8mm x 2mm J head screws with a J1 screwdriver and the two brackets from the back panel.
There will be two screws per bracket.

Remove the two black 30 mm J head screws with a J1 screwdriver to remove the long black bar.

Remove the four silver 8mm x 2mm J head screws with a J1 screwdriver and the two brackets from the back panel.

There will be two screws per bracket.

Step 6

Remove the eight silver 10mm x 1.5mm J head screws with a J1 screwdriver and the square tabs from the back panel.
Remove the eight silver 10mm J head screws with a J1 screwdriver underneath the square tabs.

Remove the eight silver 10mm x 1.5mm J head screws with a J1 screwdriver and the square tabs from the back panel.

Remove the eight silver 10mm J head screws with a J1 screwdriver underneath the square tabs.

Step 7

Remove the 36 silver 10mm J head screws with a J1 screwdriver from the back panel.

Remove the 36 silver 10mm J head screws with a J1 screwdriver from the back panel.

Step 8

Place a hand on the front panel and speakers and carefully flip the keyboard over with the keys facing up.
Having a extra pair of hands will be useful.
Grab the center of the front panel with two hands and lift to remove panel.
Grab the speakers from the sides and lift to remove. Once you have done this for the first speaker, repeat with the second speaker.

Place a hand on the front panel and speakers and carefully flip the keyboard over with the keys facing up.

Having a extra pair of hands will be useful.

Grab the center of the front panel with two hands and lift to remove panel.

Grab the speakers from the sides and lift to remove. Once you have done this for the first speaker, repeat with the second speaker.

Step 9

              Pitch Bend

Remove the two 8mm x 1.5mm J screws from the inside of the side panel by using a J1 head screwdriver.
Slide the pitch bend out of the side panel.

Remove the two 8mm x 1.5mm J screws from the inside of the side panel by using a J1 head screwdriver.

Slide the pitch bend out of the side panel.

Step 10

Follow the white and orange cable to the white end that is attached to the button panel
Pinch the white end and pull the cord out

Follow the white and orange cable to the white end that is attached to the button panel

Pinch the white end and pull the cord out

Step 11

Run the white and orange cable through the innermost side panel and pull out

Run the white and orange cable through the innermost side panel and pull out

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Areli Reyes

Member since: 10/01/2017

527 Reputation

                                      4 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team S4-G2, Livingston Fall 2017                        

                                                  Member of Cal Poly, Team S4-G2, Livingston Fall 2017 



                    CPSU-LIVINGSTON-F17S4G2                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team