Capresso Infinity Power Cord Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 30 minutes

Sections

Metal Outside Casing
8 steps
Power Cord
4 steps

Flags

BackCapresso Infinity
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Metal Outside Casing

Twist the top plastic container to the left counterclockwise.
Pull upwards to remove.

Twist the top plastic container to the left counterclockwise.

Pull upwards to remove.

1024

Step 2

Twist the top burr to the left counter clockwise.
Pull upwards to remove.

Twist the top burr to the left counter clockwise.

Step 3

Flip entire device upside down.
Remove two rubber coverings on the back of the device.

Flip entire device upside down.

Remove two rubber coverings on the back of the device.

Step 4

Remove four 11.59mm T10 screws.
The screws will have small circular washers under them. Put them aside for reassembly.

Remove four 11.59mm T10 screws.

The screws will have small circular washers under them. Put them aside for reassembly.

Step 5

Lift the metal outside casing off the black base.
Flip the outside casing forward so you have access to the inside of it.

Lift the metal outside casing off the black base.

Flip the outside casing forward so you have access to the inside of it.

Step 6

Remove one 11.59mm T10 screw.
Let the green wire fall, or place somewhere so it doesn’t get in the way.
There will be a small metal retainer and washer, put them aside for reassembly.

Remove one 11.59mm T10 screw.

Let the green wire fall, or place somewhere so it doesn’t get in the way.

There will be a small metal retainer and washer, put them aside for reassembly.

Step 7

Remove two 11.59mm T10 screws.

Remove two 11.59mm T10 screws.

Step 8

Remove the time/on switch by pulling upwards.

Remove the time/on switch by pulling upwards.

Step 9

              Power Cord

Remove two 13.60mm T10 screws.
A white, flat plastic piece will have come loose. Place this to the side for reassembly.

Remove two 13.60mm T10 screws.

A white, flat plastic piece will have come loose. Place this to the side for reassembly.

Step 10

Using a Flathead screwdriver loosen the two screws connecting the white and black wire to the plastic box.
Do not remove the screws from the box, but loosen them enough to disconnect the black and white wire.

Using a Flathead screwdriver loosen the two screws connecting the white and black wire to the plastic box.

Do not remove the screws from the box, but loosen them enough to disconnect the black and white wire.

Step 11

Originally attached to the inside of the outer casing, the green wire needs to be fed through the zip tie which keeps it in place.
Lift up on the zip tie far enough to create a space to feed the green wire through.
Place the zip tie back around the column that you lifted it from.
All three wires that comprise the power cord should be detached from the coffee grinder.

Originally attached to the inside of the outer casing, the green wire needs to be fed through the zip tie which keeps it in place.

Lift up on the zip tie far enough to create a space to feed the green wire through.

Place the zip tie back around the column that you lifted it from.

All three wires that comprise the power cord should be detached from the coffee grinder.

Step 12

Feed the wires through the small hole at the bottom of the coffee grinder where the external power cord is located.
Once the power cord is free of the coffee grinder, you are able to put in the new cord.

Feed the wires through the small hole at the bottom of the coffee grinder where the external power cord is located.

Once the power cord is free of the coffee grinder, you are able to put in the new cord.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Elizabeth Roach

Member since: 10/09/2018

233 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       USF Tampa, Team S1-G1, Leahy Fall 2018                        

                                                  Member of USF Tampa, Team S1-G1, Leahy Fall 2018 



                    USFT-LEAHY-F18S1G1                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team