Capresso Infinity Bottom Conical Burr Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          20 minutes

Sections

Metal Outside Casing
8 steps
Bottom Conical Burr
7 steps

Flags

BackCapresso Infinity
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Metal Outside Casing

Twist the top plastic container to the left counterclockwise.
Pull upwards to remove.

Twist the top plastic container to the left counterclockwise.

Pull upwards to remove.

1024

Step 2

Twist the top burr to the left counter clockwise.
Pull upwards to remove.

Twist the top burr to the left counter clockwise.

Step 3

Flip entire device upside down.
Remove two rubber coverings on the back of the device.

Flip entire device upside down.

Remove two rubber coverings on the back of the device.

Step 4

Remove four 11.59mm T10 screws.
The screws will have small circular washers under them. Put them aside for reassembly.

Remove four 11.59mm T10 screws.

The screws will have small circular washers under them. Put them aside for reassembly.

Step 5

Lift the metal outside casing off the black base.
Flip the outside casing forward so you have access to the inside of it.

Lift the metal outside casing off the black base.

Flip the outside casing forward so you have access to the inside of it.

Step 6

Remove one 11.59mm T10 screw.
Let the green wire fall, or place somewhere so it doesn’t get in the way.
There will be a small metal retainer and washer, put them aside for reassembly.

Remove one 11.59mm T10 screw.

Let the green wire fall, or place somewhere so it doesn’t get in the way.

There will be a small metal retainer and washer, put them aside for reassembly.

Step 7

Remove two 11.59mm T10 screws.

Remove two 11.59mm T10 screws.

Step 8

Remove the time/on switch by pulling upwards.

Remove the time/on switch by pulling upwards.

Step 9

              Bottom Conical Burr

Grab the edge of the plastic black ring that sits on top of the device and gently pull up to release.

Grab the edge of the plastic black ring that sits on top of the device and gently pull up to release.

Step 10

Remove the black rubber knob atop the bottom burr by gently pulling up.

Remove the black rubber knob atop the bottom burr by gently pulling up.

Step 11

Partially remove one 47.20mm T20 screw.
The screw does not need to come out completely, it just needs to be loose enough pull the burr out of the device.

Partially remove one 47.20mm T20 screw.

The screw does not need to come out completely, it just needs to be loose enough pull the burr out of the device.

Step 12

Remove the bottom burr piece by pulling upwards.
There will be 3 springs and 3 metal balls under the springs, located underneath the burr. Put them aside for reassembly.

Remove the bottom burr piece by pulling upwards.

There will be 3 springs and 3 metal balls under the springs, located underneath the burr. Put them aside for reassembly.

Step 13

Remove the loosened screw by pulling it upwards.

Remove the loosened screw by pulling it upwards.

Step 14

Grip the plastic piece at the top of the conical burr and pull upwards to remove.
Grip the metal burr, and pull upwards to slide it off the plastic base.

Grip the plastic piece at the top of the conical burr and pull upwards to remove.

Grip the metal burr, and pull upwards to slide it off the plastic base.

Step 15

              Spring and Bearing Positions

This is the correct position of bearings and springs when the screw and bottom burr are removed.

This is the correct position of bearings and springs when the screw and bottom burr are removed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 2 other contributors

                    Nina Mackin

Member since: 10/09/2018

447 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       USF Tampa, Team S1-G1, Leahy Fall 2018                        

                                                  Member of USF Tampa, Team S1-G1, Leahy Fall 2018 



                    USFT-LEAHY-F18S1G1                     


                                            4 Members                     


                                            5 Guides authored

dorthe - Jul 15, 2019

Step 5. In my machine there are 5 taps im bottom that has to be released with a screwdriver, before outer cap can be liftet up.

Step 9, It is essential to mark the location of black plastic ring in regards to white plastic part with holes AND in regards to ex. white square plastic part before removing part. Othervise you can’t assemble or you could destroy the burrs when you adjust the grinder to very fine grinds

Raj haraniya - Aug 24, 2019

Hi is it possible to remove the top burr? If yes how?

Thanks

Craven Morehead - Dec 10, 2019

Great description of how to remove the bottom burr. Would be even greater if a new burr was available, which it is not.

gt76us - Apr 30, 2020

burrs were found for sale on ebay. they come in a matched set. i got a set for 30 dollars. also it seems the upper burr has to be center punched out of the plastic housing it is in but i am just making an educated guess.

bradley shefmire - Oct 10, 2020

wow - Appreciate the instructions but…….screw this….$85 for a new whole new Capresso Infinity Conical Grinder….. https://www.amazon.com/gp/product/B0000A…

Introduction#

What you need#

Team#

Introduction

What you need

Team